Search found 263 matches
- Tue Apr 23, 2024 5:01 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 37
- Views: 1367
Re: Centroid Operator Control Panel Interface Board: USB-BOB
On page 13 of the draft manual, there's a wiring diagram for an SPST button. I am installing a 3-position rotary switch to set up for 1x, 10x, 100x speed multipliers for the X and Z MPGs on my lathe. Attached is a photo of the back of the switch. I think the way I'd wire this, based on the manual i...
- Tue Apr 23, 2024 8:54 am
- Forum: Centroid Acorn CNC Controller
- Topic: Serious Issues with existing build
- Replies: 7
- Views: 173
Re: Serious Issues with existing build
Alright, glad you're making progress!
- Mon Apr 22, 2024 10:04 am
- Forum: Centroid Acorn CNC Controller
- Topic: Serious Issues with existing build
- Replies: 7
- Views: 173
Re: Serious Issues with existing build
Is it possible that the Clearpath internal hard stop homing was accidentally enabled?
- Mon Apr 22, 2024 9:09 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X Axis problems Hardinge Lathe
- Replies: 3
- Views: 134
Re: X Axis problems Hardinge Lathe
Hello, that board should still be within the warranty period of 12 months.
For more information, please look here: https://www.centroidcnc.com/centroid_di ... ranty.html
For more information, please look here: https://www.centroidcnc.com/centroid_di ... ranty.html
- Fri Apr 19, 2024 1:53 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 37
- Views: 1367
Re: Centroid Operator Control Panel Interface Board: USB-BOB
What type of inputs do you want to be preprogrammed by Centroid and included with the Wizard? One that might be useful (though may not need to be in the wizard, I'm not sure) - is an override enable/disable. I want to have to hit a switch to enable the feed and spindle speed override knobs, so that...
- Fri Apr 19, 2024 1:31 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 37
- Views: 1367
Re: Centroid Operator Control Panel Interface Board: USB-BOB
Is that a 9mm mounting hole for the rotary encoders? or something different? Most of the ones I've used and have kicking around here with a 6mm shaft have a 9mm mounting diameter. Just checking before I start drilling! Yes, you should do a clearance fit for M9x0.75 threads + 3mm diameter hole ( or ...
- Thu Apr 18, 2024 2:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 22
- Views: 451
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
What exact model ASDA-B2 drives do you have? It will say on the nameplate sticker. Please post a picture of the connector and nameplate sticker if you can. I am curious because all of Delta's documentation for ASD-B2-xxxx-B (standard spec) drives shows a 44 pin CN1 connector. The ASD-B2-xxxx-F spec ...
- Thu Apr 18, 2024 2:08 pm
- Forum: Centroid Hickory CNC Controller
- Topic: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
- Replies: 96
- Views: 5463
Re: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
Question about encoder cable. Once the rest of the retrofit is complete I am planning to retrofit the air driven tool turret with a servo motor. I am using Leadshine EL7 drives and servos with absolute encoders. The encoder cable already has the motor connector on it and it is impossible to get it ...
- Thu Apr 18, 2024 11:58 am
- Forum: Centroid Hickory CNC Controller
- Topic: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
- Replies: 96
- Views: 5463
Re: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
Question about encoder cable. Once the rest of the retrofit is complete I am planning to retrofit the air driven tool turret with a servo motor. I am using Leadshine EL7 drives and servos with absolute encoders. The encoder cable already has the motor connector on it and it is impossible to get it ...
- Thu Apr 18, 2024 9:00 am
- Forum: Centroid Hickory CNC Controller
- Topic: Breaking news! Delta B3A ethercat drive is now running with Hickory and we are doing final tests on a machine
- Replies: 7
- Views: 314
Re: Breaking news! Delta B3A ethercat drive is now running with Hickory and we are doing final tests on a machine
For Hickory, the main tuning done on the Centroid side is the delay. If you have scales, that will add another position loop on top.