Search found 275 matches
- Wed May 08, 2024 2:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading a Gorilla CNC from Flashcut to Acorn
- Replies: 11
- Views: 101
Re: Upgrading a Gorilla CNC from Flashcut to Acorn
Hi Centroid467, As I understand from most replies I have received from the community, members do not clearly understand the subtle differences between Sink and Source output with common ground in Source configuration or common supply in Sink configuration. As an electronic circuit designer, I will ...
- Wed May 08, 2024 11:40 am
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading a Gorilla CNC from Flashcut to Acorn
- Replies: 11
- Views: 101
Re: Upgrading a Gorilla CNC from Flashcut to Acorn
Hello Daniel, You are right that the 74ACT125 tri-state buffers on the DB25 outputs will both sink and source current so wire them as in the DB25 drawings. I could not find any documentation on your specific drives and I suspect they might be a customized version for Gorilla CNC but from the 7th pag...
- Tue May 07, 2024 12:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Server motorsport run after update of CNC 12
- Replies: 5
- Views: 127
Re: Server motorsport run after update of CNC 12
Hello Steve, There should be a page in the Wizard under "DB25 Connector" labelled "Mapping". There will be a drop down menu to select DB25 or Screw Terminal near the top of the page. See page 95 in the ACORN installation manual for some nice pictures: https://www.centroidcnc.com/...
- Tue May 07, 2024 10:50 am
- Forum: Centroid Acorn CNC Controller
- Topic: Server motorsport run after update of CNC 12
- Replies: 5
- Views: 127
Re: Server motorsport run after update of CNC 12
Hello, I am taking a look at your report and I see that your CPU (Core 2 Duo P7570) is below our minimum requirements for good performance. However, I do not believe that is your main issue here. As it has been a while since the machine was last used, I would go through and verify that all the wirin...
- Mon May 06, 2024 4:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New build - Novakon Pulsar
- Replies: 5
- Views: 218
Re: New build - Novakon Pulsar
Hello, If the spindle driver outputs differential quadrature encoder signals and the servo is belted 1:1 with the spindle then yes you should be able to use it for rigid tapping. If it is not belted 1:1 then you will need an encoder that is belted 1:1 with the spindle. Yes, there are gear ratio para...
- Fri May 03, 2024 9:14 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Can Centroid Control this?
- Replies: 24
- Views: 385
Re: Can Centroid Control this?
Hello, I've seen some DC motors with both tachogenerator feedback and encoder feedback. I see a lot of references to "measuring system" inputs on the controller and they sure look a lot like encoder inputs to me. The language in the manual suggests that they are linear encoders on the axes...
- Thu May 02, 2024 10:19 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Can Centroid Control this?
- Replies: 24
- Views: 385
Re: Can Centroid Control this?
I believe you would be able to control these with an Oak in velocity mode. The wiring would probably be a little annoying since it looks like you'll have to wire the encoders directly to the Oak rather than to the drive. From reading the manual, I would try wiring like this for velocity mode: pin 1 ...
- Wed May 01, 2024 11:19 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 51
- Views: 2980
Re: Centroid Operator Control Panel Interface Board: USB-BOB
Connected now. What I found out ist that the 5m extension is only working with max. 0.5m primary USB cable. Makes sense, because by standard USB2.0 is limited to 5m. Will the first Opcon work after update also? Uwe We're not planning on breaking existing OPCON functionality. USBBOB uses an expanded...
- Mon Apr 29, 2024 10:51 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 51
- Views: 2980
Re: Centroid Operator Control Panel Interface Board: USB-BOB
This was my (pre-caffeinated) thought. So does that mean I don't need the resistor at all in this case? If so, would I be better off wiring it like they outline, so that the LED power is controlled by the button, or would it be better to wire the LED directly to the USB-BOB's 5V and COM, and then t...
- Mon Apr 29, 2024 10:48 am
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 5
- Views: 222
Re: AC Servo suggestions?
There is only analog control output on ACORN and ACORNSIX for spindles.