Search found 597 matches
- Tue Feb 11, 2025 10:22 am
- Forum: CNC Plasma
- Topic: Toroidal power supply question
- Replies: 2
- Views: 103
Re: Toroidal power supply question
That's expected from wiring in a transformer. Coils are just coils of wire after all. They'll have some DC resistance but not very much. If I remember correctly, you are using a circuit breaker upstream of this toroidal supply. I would flip the switch on the breaker to disconnect the toroid from the...
This post has been liked 1 time(s).
- Fri Feb 07, 2025 3:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Bought an Acorn board already installed for a change, need a hand...
- Replies: 39
- Views: 5207
Re: Bought an Acorn board already installed for a change, need a hand...
Yes, I would put that rightmost ground to the COM pin on the analog output header.
This post has been liked 1 time(s).
- Tue Feb 11, 2025 10:05 am
- Forum: CNC Plasma
- Topic: Voltage divider/ cable ?
- Replies: 6
- Views: 1515
Re: Voltage divider/ cable ?
I have a prime weld cut 60 plasma cutter and the centroid cable from the plasma cutter to the THC board. I'm planning on changing the internal voltage divider to a proma voltage divider. My question is once I've changed the voltage divider to the proma unit can I still use the same cable from the p...
This post has been liked 0 time(s).
- Mon Feb 10, 2025 1:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: G-Code
- Replies: 1
- Views: 121
Re: G-Code
If I am understanding you correctly, you need the Mozaik Cabinet software to output GCode for Centroid? They appear to already have a Centroid postprocessor included or available. Does that postprocessor not work for your machine?
This post has been liked 0 time(s).
- Mon Feb 10, 2025 11:57 am
- Forum: Centroid Hickory EtherCAT CNC Controller
- Topic: Millport VMC1660 Centroid Upgrade (Leadshine EL7)
- Replies: 12
- Views: 6055
Re: Millport VMC1660 Centroid Upgrade (Leadshine EL7)
In the pictured schematics, it looks to me like that spindle chiller would be turned on by CNT4 when CNT1 is closed (not in E-stop) and PLCIO2 H7 OUT 30 is closed. To replicate that on S15259, I would add a CNT5 and OCR4 following the pattern of the CNT2/OCR2 block. Of course, you'll need to put the...
This post has been liked 0 time(s).
- Mon Feb 10, 2025 9:58 am
- Forum: Centroid Acorn CNC Controller
- Topic: Retrofit Acorn to full blown Acorn Six
- Replies: 44
- Views: 6056
Re: Retrofit Acorn to full blown Acorn Six
Sounds like someone is making a really cool model DC-3.suntravel wrote: ↑Sun Feb 09, 2025 11:01 amNa, at the moment I have to make parts to earn some money...Black Forest wrote: ↑Sun Feb 09, 2025 10:53 amYou have had enough time to figure out a part to make with 5 axis! Get to it. We want a video.
![]()
28 Cylinders for two 14 cylinder radial model engines.
Uwe
This post has been liked 0 time(s).
- Fri Feb 07, 2025 5:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: AUX MPG Inputs on MPG terminals of USBBOB
- Replies: 5
- Views: 704
Re: AUX MPG Inputs on MPG terminals of USBBOB
USBBOB communications protocol information is attached to this post. It is very similar to the Ether1616 protocol.
This post has been liked 0 time(s).
- Fri Feb 07, 2025 2:49 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Anilam Crusader series M converting to Allin1DC
- Replies: 47
- Views: 4927
Re: Anilam Crusader series M converting to Allin1DC
No ventilation at all? It should be fine like that.
However, our recommended cabinet setup is a sealed cabinet with filtered intake fans mounted towards the bottom and unfiltered air exits near the top. Our stock and custom built system cabinets have louvers near the top of the door.
However, our recommended cabinet setup is a sealed cabinet with filtered intake fans mounted towards the bottom and unfiltered air exits near the top. Our stock and custom built system cabinets have louvers near the top of the door.
This post has been liked 0 time(s).
- Fri Feb 07, 2025 2:01 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Anilam Crusader series M converting to Allin1DC
- Replies: 47
- Views: 4927
Re: Anilam Crusader series M converting to Allin1DC
I don't recommend having unfiltered fans blowing across the ALLIN1DC even if the cabinet air intake itself is properly filtered. I've seen enough drives damaged by conductive dust blown into them to recommend against that.
This post has been liked 0 time(s).
- Fri Feb 07, 2025 11:33 am
- Forum: Centroid Acorn CNC Controller
- Topic: Deckel fP4A Dialog11
- Replies: 9
- Views: 877
Re: Deckel fP4A Dialog11
I cannot say I have done such a retrofit and I have not seen any Deckel specific documentation but from what I have read about those machines, a Centroid controller would do very well. I read that model would have Siemens DC servos fitted with Bosch amplifiers. If you can get specifications for the ...
This post has been liked 0 time(s).