Touch Screen Monitors
Moderator: cnckeith
-
- Posts: 28
- Joined: Tue Jan 02, 2018 6:26 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Touch Screen Monitors
Would I be able to rotate my monitor 90 degrees ? like a portrait orientation then
Fitting the VCP below the main screen instead of been at the right side ?
Please have a look at the attached pic.
Thanks.
Fitting the VCP below the main screen instead of been at the right side ?
Please have a look at the attached pic.
Thanks.
-
- Posts: 595
- Joined: Tue Sep 12, 2017 10:03 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 1030090099
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Outside Winston-Salem, NC
- Contact:
Re: Touch Screen Monitors
Clay
near Winston-Salem, NC
unofficial ACORN fb group https://www.facebook.com/groups/897054597120437/
near Winston-Salem, NC
unofficial ACORN fb group https://www.facebook.com/groups/897054597120437/
-
- Posts: 286
- Joined: Thu Mar 18, 2010 2:24 pm
Re: Touch Screen Monitors
That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
When requesting support, please ALWAYS post a current report. Find out how to take a report from your Acorn, CNC11 or CNC10 system here: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
If your question is PLC, Macro or program related, please also post a copy of the program or macro as well.
Without the above information we may not be able to help and/or reply until the required information is posted..
If your question is PLC, Macro or program related, please also post a copy of the program or macro as well.
Without the above information we may not be able to help and/or reply until the required information is posted..
-
- Posts: 9915
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Touch Screen Monitors
I hope Scott didn't give you the LOOK.Centroid_Tech wrote: ↑Wed Jan 10, 2018 1:43 pm That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 2208
- Joined: Sat Nov 18, 2017 2:32 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: Yes
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: Acorn 238
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Bergland, MI, USA
- Contact:
Re: Touch Screen Monitors
While we are on the subject, is there a setting that would make the CNC12 and VCP ~50 to 100 pixels smaller? Depending on the monitor some of my setups go off the screen edge by 20-25 pixels
-
- Posts: 114
- Joined: Wed Sep 11, 2013 1:31 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 0916130849
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: No
Re: Touch Screen Monitors
$212.84 on amazon is cheaper but your post got me looking on ebay and i sent an offer to a seller and got a new in open box 2nd pct2235 coming from a seller for $170 shipped. So thank you indirectly. Never hurts to send an offer.frijoli wrote: ↑Mon Jan 08, 2018 10:17 pm On ebay, Planar monitor from the FB page
https://l.facebook.com/l.php?u=https%3A ... SrQ0sVyHTo
Mikie in Bloomington IL
-
- Posts: 9915
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Touch Screen Monitors
I have this issue with the Wizard on the ASUS 15.6" VT168-H, I have to scroll down a bit. I have used several Touchscreens and no real problem with the CNC12 screens.Gary Campbell wrote: ↑Wed Jan 10, 2018 10:33 pm While we are on the subject, is there a setting that would make the CNC12 and VCP ~50 to 100 pixels smaller? Depending on the monitor some of my setups go off the screen edge by 20-25 pixels
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 9915
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Touch Screen Monitors
PURDY, but don't dismiss the ASUS VT207N 19.5" and less than $200, sometimes refurbs can be found for much less.frijoli wrote: ↑Mon Jan 08, 2018 10:17 pm On ebay, Planar monitor from the FB page
https://l.facebook.com/l.php?u=https%3A ... SrQ0sVyHTo
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 28
- Joined: Tue Jan 02, 2018 6:26 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Touch Screen Monitors
That would be great if in future upgrade releases we can have this option , like when you dock or / and drag a windows on screen, then once set you can save the changes and always boot the software up on screen.Centroid_Tech wrote: ↑Wed Jan 10, 2018 1:43 pm That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
This would save a lot of space if you are installing the monitor on a side panel, basically for small machines.
-
- Posts: 28
- Joined: Tue Jan 02, 2018 6:26 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Touch Screen Monitors
Hi guys , you may want to check at Best Buy on Ebay, I got the ASUS VT207 brand new for $180.martyscncgarage wrote: ↑Thu Jan 11, 2018 10:43 amPURDY, but don't dismiss the ASUS VT207N 19.5" and less than $200, sometimes refurbs can be found for much less.frijoli wrote: ↑Mon Jan 08, 2018 10:17 pm On ebay, Planar monitor from the FB page
https://l.facebook.com/l.php?u=https%3A ... SrQ0sVyHTo
Marty