I am looking at a purchase of older machine. Want to investigate how much it would take to retrofit. I could only get to the Z servo. Was not able to get into the cabinet as another machine was pushed up against it. So not sure I am providing all the info that is needed but here it is anyway.
Mitshubishi M-v5b 1994
Servo HA100NBS-A33
100 NCB-S
2kw 2000 rpm
Encoder ABS 25000 p/rev
Mitshubishi Servo with Oak
Moderator: cnckeith
-
- Posts: 6
- Joined: Sat Feb 03, 2018 10:52 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: 1128180712
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
-
- Posts: 433
- Joined: Mon Jul 18, 2011 9:57 am
- Allin1DC CNC Controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Mitshubishi Servo with Oak
Do you know what kind of drives are on it? If they drives accept velocity (-10 to +10v) or position control we could interface with them with our Oak. We would also need a differential quadrature signal, simulated from the drives is fine (as the servo has absolute). If they drives are not compatible its still possible we could run that servomotor with our ACDC drives. But it would need new encoders installed and for us to get one of them in here to figure out the PID settings.
Alternatively a 2kW Estun AC Motor/Drive Combo is about $1300. Sell the old stuff on eBay to get most of the cost back and start fresh with all new stuff.
Alternatively a 2kW Estun AC Motor/Drive Combo is about $1300. Sell the old stuff on eBay to get most of the cost back and start fresh with all new stuff.
When requesting support READ THIS POST first. https://www.viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
-
- Posts: 6
- Joined: Sat Feb 03, 2018 10:52 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: 1128180712
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Mitshubishi Servo with Oak
Sorry for the delay. I finally was able to get the the control panel and get it open.
The servo driver model is: MSD-A-SVJ-10
I have yet to determine what the drives accept for control. {D-A} 1 channel, 7bit, 0-10volt
https://s3.amazonaws.com/Icarus/DOCUMEN ... 5F3277.pdf
I found this on MSD-B-SVJ External analog output
-/+ 10V, 2ch
I need to go recheck but odd that the dash 10 is for 1kw servo. My z axis is 2kw.
Maximum input pulse frequency (Position control mode): 500 kpps- when using differential receiver, 200 kpps- when using open collector.
The servo driver model is: MSD-A-SVJ-10
I have yet to determine what the drives accept for control. {D-A} 1 channel, 7bit, 0-10volt
https://s3.amazonaws.com/Icarus/DOCUMEN ... 5F3277.pdf
I found this on MSD-B-SVJ External analog output
-/+ 10V, 2ch
I need to go recheck but odd that the dash 10 is for 1kw servo. My z axis is 2kw.
Maximum input pulse frequency (Position control mode): 500 kpps- when using differential receiver, 200 kpps- when using open collector.
-
- Posts: 10
- Joined: Sat Dec 30, 2017 5:18 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Utah, USA
- Contact:
Re: Mitshubishi Servo with Oak
I just picked up a machine with similar drives. I was just wondering if you were able to use them with an oak?
-
- Posts: 9915
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Mitshubishi Servo with Oak
Please take pictures of the MOTOR lables AND the Drives and their labels and post them here.Extreme Industrial wrote: ↑Wed Mar 11, 2020 12:59 pm I just picked up a machine with similar drives. I was just wondering if you were able to use them with an oak?
Centroid can't guess at what you have...
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ