when I close the circle of a circle or a oblong as in this example, Intercon puts a move on the circle. what is the procedure to stop this?
Intercon circle close
Moderator: cnckeith
-
- Posts: 15
- Joined: Sat Feb 03, 2018 11:42 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: K102811
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Fowler MI
Intercon circle close
- Attachments
-
- 8x16 gage pin 2.icn
- (4.65 KiB) Downloaded 82 times
-
- 8x16 gage pin 2.cnc
- (1.68 KiB) Downloaded 107 times
Re: Intercon circle close
Don't forget to cancel cutter comp when you are done with the path, before you move X/Y anywhere else.
You probably want Comp Off after operation 19 in your example.
You probably want Comp Off after operation 19 in your example.
-
- Posts: 15
- Joined: Sat Feb 03, 2018 11:42 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: K102811
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Fowler MI
Re: Intercon circle close
i finally figured out the screen shot
the two arcs going back to the left is what i am referring to
the two arcs going back to the left is what i am referring to
-
- Posts: 15
- Joined: Sat Feb 03, 2018 11:42 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: K102811
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Fowler MI
Re: Intercon circle close
i thought there was an auto off to the comp.
it has been since the late 80's i programmed anything like this. the pronest i used on the plasma i programmed did all of that for me.
it has been since the late 80's i programmed anything like this. the pronest i used on the plasma i programmed did all of that for me.
-
- Posts: 7411
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Intercon circle close
looking at the .icn program.. the comp was never turned off.
i go over how to program intercon and cutter comp in detail in the mill training video.
viewtopic.php?f=61&t=2118
i go over how to program intercon and cutter comp in detail in the mill training video.
viewtopic.php?f=61&t=2118
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html