Page 2 of 8
Re: Touch Screen Monitors
Posted: Wed Jan 03, 2018 3:23 pm
by Rolquin
Would I be able to rotate my monitor 90 degrees ? like a portrait orientation then
Fitting the VCP below the main screen instead of been at the right side ?
Please have a look at the attached pic.
Thanks.
Re: Touch Screen Monitors
Posted: Mon Jan 08, 2018 10:17 pm
by frijoli
Re: Touch Screen Monitors
Posted: Wed Jan 10, 2018 1:43 pm
by Centroid_Tech
That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
Re: Touch Screen Monitors
Posted: Wed Jan 10, 2018 9:27 pm
by martyscncgarage
Centroid_Tech wrote: ↑Wed Jan 10, 2018 1:43 pm
That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
I hope Scott didn't give you the LOOK.
Re: Touch Screen Monitors
Posted: Wed Jan 10, 2018 10:33 pm
by Gary Campbell
While we are on the subject, is there a setting that would make the CNC12 and VCP ~50 to 100 pixels smaller? Depending on the monitor some of my setups go off the screen edge by 20-25 pixels
Re: Touch Screen Monitors
Posted: Thu Jan 11, 2018 1:53 am
by bloomingtonmike
$212.84 on amazon is cheaper but your post got me looking on ebay and i sent an offer to a seller and got a new in open box 2nd pct2235 coming from a seller for $170 shipped. So thank you indirectly. Never hurts to send an offer.
Re: Touch Screen Monitors
Posted: Thu Jan 11, 2018 10:41 am
by martyscncgarage
Gary Campbell wrote: ↑Wed Jan 10, 2018 10:33 pm
While we are on the subject, is there a setting that would make the CNC12 and VCP ~50 to 100 pixels smaller? Depending on the monitor some of my setups go off the screen edge by 20-25 pixels
I have this issue with the Wizard on the ASUS 15.6" VT168-H, I have to scroll down a bit. I have used several Touchscreens and no real problem with the CNC12 screens.
Re: Touch Screen Monitors
Posted: Thu Jan 11, 2018 10:43 am
by martyscncgarage
PURDY, but don't dismiss the ASUS VT207N 19.5" and less than $200, sometimes refurbs can be found for much less.
Marty
Re: Touch Screen Monitors
Posted: Thu Jan 11, 2018 10:47 am
by Rolquin
Centroid_Tech wrote: ↑Wed Jan 10, 2018 1:43 pm
That is something that is easier said than done. There is a lot of coding, that is static, that is in place for the layout of the current virtual control panel. I have mentioned it to our software department to see if the orientation of the virtual control panel can be easily changed at some point in the future.
That would be great if in future upgrade releases we can have this option , like when you dock or / and drag a windows on screen, then once set you can save the changes and always boot the software up on screen.
This would save a lot of space if you are installing the monitor on a side panel, basically for small machines.
Re: Touch Screen Monitors
Posted: Thu Jan 11, 2018 10:51 am
by Rolquin
martyscncgarage wrote: ↑Thu Jan 11, 2018 10:43 am
PURDY, but don't dismiss the ASUS VT207N 19.5" and less than $200, sometimes refurbs can be found for much less.
Marty
Hi guys , you may want to check at Best Buy on Ebay, I got the ASUS VT207 brand new for $180.