I would rather repin a connector than splice the cables between my Acorn and Logosol drives.
The connector says MXN-15 2695
My guess would be Molex but cant find any such model.
This is an 8 pin connector but I am interested in the pins themselves.
Any help would be great. I seem to see this style connector often.
Connector and Pin ID?
Moderator: cnckeith
-
- Posts: 132
- Joined: Fri Nov 03, 2017 12:19 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Conroe, TX
Connector and Pin ID?
1st Acorn project. G0704/BDTools/Hoss Conversion De"maching"
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
Re: Connector and Pin ID?
Those are called KK connectors. Also commonly called Waldom connectors. There are a couple different common sizes, identified by the pin pitch.
See http://www.mattmillman.com/info/crimpconnectors/#kk100, or http://www.mattmillman.com/info/crimpconnectors/#kk156
Components are readily available from Digikey and others.
See http://www.mattmillman.com/info/crimpconnectors/#kk100, or http://www.mattmillman.com/info/crimpconnectors/#kk156
Components are readily available from Digikey and others.
-
- Posts: 132
- Joined: Fri Nov 03, 2017 12:19 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Conroe, TX
Re: Connector and Pin ID?
Thanks so much, got them ordered
1st Acorn project. G0704/BDTools/Hoss Conversion De"maching"
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
-
- Posts: 132
- Joined: Fri Nov 03, 2017 12:19 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Conroe, TX
Re: Connector and Pin ID?
Those worked out very well.
Originally I was going to put a din rail and terminals to extend the cables.
This turned out much cleaner and the cables will go direct to the Acorn. Much less potential for noise and errors.
Originally I was going to put a din rail and terminals to extend the cables.
This turned out much cleaner and the cables will go direct to the Acorn. Much less potential for noise and errors.
1st Acorn project. G0704/BDTools/Hoss Conversion De"maching"
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)