https://www.cde.com/resources/catalogs/288P.pdf
Thanks,
Kevin
Quencharc substitute?
Moderator: cnckeith
-
kevincnc
- Posts: 58
- Joined: Thu May 16, 2019 8:42 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 780473842B28-0131191600
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Quencharc substitute?
Hi all, I'm just wondering if a .22uF 100 ohm, 400 volt snubber would work.
https://www.cde.com/resources/catalogs/288P.pdf
Thanks,
Kevin
https://www.cde.com/resources/catalogs/288P.pdf
Thanks,
Kevin
-
Fastest1
- Posts: 132
- Joined: Fri Nov 03, 2017 12:19 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Conroe, TX
Re: Quencharc substitute?
I dont see any support for 3rd party products or implementation of them on the Centroid forum.
1st Acorn project. G0704/BDTools/Hoss Conversion De"maching"
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
Leadshine MX 3660
Repurposed above Acorn (#194) and an Ethernet 1616 to a UMC-10 with an 8 position tool changer.
CNC12 Pro/Digitizing ver 4.64 (1/31/2022)
-
Upnorth
- Posts: 237
- Joined: Wed Apr 01, 2020 8:23 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 1702
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Quencharc substitute?
I would use the snubbers that Centroid recommends.
However, If I had the snubbers you mention in your link I would use them.
However, If I had the snubbers you mention in your link I would use them.
Last edited by Upnorth on Thu Mar 03, 2022 7:31 am, edited 1 time in total.
-
ShawnM
- Posts: 2234
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Quencharc substitute?
Also check if the manufacturer of the contactor (if this is for a contactor) makes their own "snubbers". I have dozens of Siemens contactors pulled from an industrial CNC router and they all have a Siemens RC snubber attached to them.
-
kevincnc
- Posts: 58
- Joined: Thu May 16, 2019 8:42 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 780473842B28-0131191600
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Quencharc substitute?
Thanks for the replies. I see that the ideal value can be calculated based upon the use, so I assume that the recommended one is a good compromise. I just don't know how much a little variation matters without taking the time to research more. I learned years ago to put a MOV across relay coils, and that's the extent of my arc suppression knowledge. I'm not having any trouble with nothing on the coils at all, so I guess anything would be better than nothing.
Kevin
Kevin