Trying to setup a conductive touch block on my router, using the new Acorn controller. I setup pin 7 as my input using the wizard and the touch sequence works. But now I'm wondering how to tell the controller how thick my touch block is. I've been a Mach user for years and am trying to relate this to the method that is used in Mach.
Bob
TT-1 configuration file setup, for Acorn Control.
Moderator: cnckeith
-
- Posts: 7166
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: TT-1 configuration file setup, for Acorn Control.
are you using the tt-1 to measure tools or set a part zero or both?
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 6
- Joined: Sat Nov 25, 2017 1:03 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: System ID 38D2693D45EA-0112180532
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: TT-1 configuration file setup, for Acorn Control.
To set part zero.
-
- Posts: 7166
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: TT-1 configuration file setup, for Acorn Control.
is it a home built unit? if so, how thick is it?
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 6
- Joined: Sat Nov 25, 2017 1:03 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: System ID 38D2693D45EA-0112180532
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: TT-1 configuration file setup, for Acorn Control.
Yes it's a homemade block and measured 3"x3x0.745"thick.
Is there a location in the config menu to set the block height?
We have found in the config. Parm #71 that mentions detector height. It was set to zero.
Is there a location in the config menu to set the block height?
We have found in the config. Parm #71 that mentions detector height. It was set to zero.