Page 2 of 2
Re: Output Control Both Auto and Manual
Posted: Mon Jan 08, 2018 4:14 pm
by legacytorch
Code: Select all
N0010 (Filename: Untitled.tap)
N0020 (Post processor: Centroid plasma.scpost)
N0030 (Date: 2018-01-08)
N0040 G20 (Units: Inches)
N0050 (Part: Untitled)
N0060 (Operation: Outside Offset, 0, T1: Flame, 0.0591 inch kerf)
N0070 M06 T1 F3.937 (Flame, 0.0591 inch kerf)
N0080 G00 Z0.3937
N0090 X11.3860 Y2.3616
N0100 Z0.1181
N0110 Z0.0591
N0120 M07
N0130 G04 P4
N0140 Z0.1181
N0150 M08
N0160 G01 Z0.0591 F3.937
N0170 X11.1337 Y2.3937
N0180 G02 X11.1337 Y2.3937 I0.5625 J0.0000
N0190 M12
N0200 G04 P2
N0210 G00 Z0.3937
N0220 X11.6962 Y1.3937
N0230 Z0.1181
N0240 Z0.0591
N0250 M07
N0260 G04 P4
N0270 Z0.1181
N0280 M08
N0290 G01 Z0.0591
N0300 X14.9462
N0310 M12
N0320 G04 P2
N0330 G00 Z0.3937
N0340 X14.6360 Y2.3616
N0350 Z0.1181
N0360 Z0.0591
N0370 M07
N0380 G04 P4
N0390 Z0.1181
N0400 M08
N0410 G01 Z0.0591
N0420 X14.3837 Y2.3937
N0430 G02 X14.3837 Y2.3937 I0.5625 J0.0000
N0440 M12
N0450 G04 P2
N0460 G00 Z0.3937
N0470 X8.1360 Y2.3616
N0480 Z0.1181
N0490 Z0.0591
N0500 M07
N0510 G04 P4
N0520 Z0.1181
N0530 M08
N0540 G01 Z0.0591
N0550 X7.8837 Y2.3937
N0560 G02 X7.8837 Y2.3937 I0.5625 J0.0000
N0570 M12
N0580 G04 P2
N0590 G00 Z0.3937
N0600 X5.1962 Y1.3937
N0610 Z0.1181
N0620 Z0.0591
N0630 M07
N0640 G04 P4
N0650 Z0.1181
N0660 M08
N0670 G01 Z0.0591
N0680 X8.4462
N0690 M12
N0700 G04 P2
N0710 G00 Z0.3937
N0720 X4.8860 Y2.3616
N0730 Z0.1181
N0740 Z0.0591
N0750 M07
N0760 G04 P4
N0770 Z0.1181
N0780 M08
N0790 G01 Z0.0591
N0800 X4.6337 Y2.3937
N0810 G02 X4.6337 Y2.3937 I0.5625 J0.0000
N0820 M12
N0830 G04 P2
N0840 G00 Z0.3937
N0850 Y3.3642
N0860 Z0.1181
N0870 Z0.0591
N0880 M07
N0890 G04 P4
N0900 Z0.1181
N0910 M08
N0920 G01 Z0.0591
N0930 X15.5087
N0940 G02 X15.9792 Y2.8937 I0.0000 J-0.4704
N0950 G01 Y0.8937
N0960 G02 X15.5087 Y0.4233 I-0.4704 J0.0000
N0970 G01 X4.6337
N0980 G02 X4.1633 Y0.8937 I0.0000 J0.4704
N0990 G01 Y2.8937
N1000 G02 X4.6337 Y3.3642 I0.4704 J0.0000
N1010 M12
N1020 G04 P2
N1030 G00 Z0.3937
N1040 X4.1042 Y0.8937
N1050 Z0.1181
N1060 Z0.0591
N1070 M07
N1080 G04 P4
N1090 Z0.1181
N1100 M08
N1110 G01 Z0.0591
N1120 G03 X4.6337 Y0.3642 I0.5296 J0.0000
N1130 G01 X15.5087
N1140 G03 X16.0383 Y0.8937 I0.0000 J0.5296
N1150 G01 Y2.8937
N1160 G03 X15.5087 Y3.4233 I-0.5296 J0.0000
N1170 G01 X4.6337
N1180 G03 X4.1133 Y2.9918 I-0.0000 J-0.5295
N1190 G01 X3.9629 Y3.2642
N1200 G03 X3.9111 Y3.2356 I-0.0259 J-0.0143
N1210 G01 X4.1042 Y2.8861
N1220 Y0.8937
N1230 M12
N1240 G04 P2
N1250 G00 Z0.3937
N1260 M05
N1270 M30
Program hangs at N0130 G04 P4, and all subsequent G04
Re: Output Control Both Auto and Manual
Posted: Mon Jan 08, 2018 4:31 pm
by diycncscott
My bad. I left the "feedhold while waiting for auto coolant mode" logic in. Works now.
Re: Output Control Both Auto and Manual
Posted: Mon Jan 08, 2018 4:34 pm
by cnckeith
legacytorch, how about a video clip of the machine in action? i'm sure i'm not the only one that would like to see it! -k
Re: Output Control Both Auto and Manual
Posted: Mon Jan 08, 2018 5:24 pm
by legacytorch
Thanks again Scott! Everything works perfect now.
For sure I will post a video when I get a chance.
To everyone reading this... Don't be afraid of the paid tech support. Total value for money, I couldn't be happier.
Re: Output Control Both Auto and Manual
Posted: Mon Jan 08, 2018 8:34 pm
by frijoli
cnckeith wrote: ↑Mon Jan 08, 2018 4:34 pm
legacytorch, how about a video clip of the machine in action? i'm sure i'm not the only one that would like to see it! -k
I want to see it!!!
Re: Output Control Both Auto and Manual
Posted: Wed Jan 10, 2018 8:23 am
by Black Forest
frijoli wrote: ↑Mon Jan 08, 2018 8:34 pm
cnckeith wrote: ↑Mon Jan 08, 2018 4:34 pm
legacytorch, how about a video clip of the machine in action? i'm sure i'm not the only one that would like to see it! -k
I want to see it!!!
Me too!
Re: Output Control Both Auto and Manual
Posted: Wed Jan 10, 2018 11:07 am
by DICKEYBIRD
cnckeith wrote: ↑Mon Jan 08, 2018 4:34 pm
legacytorch, how about a video clip of the machine in action? i'm sure i'm not the only one that would like to see it! -k
Me three!
Re: Output Control Both Auto and Manual
Posted: Mon Feb 12, 2018 12:29 am
by martyscncgarage
legacytorch wrote: ↑Mon Jan 08, 2018 5:24 pm
Thanks again Scott! Everything works perfect now.
For sure I will post a video when I get a chance.
To everyone reading this... Don't be afraid of the paid tech support. Total value for money, I couldn't be happier.
We're interested in seeing the machine.
As for the paid support I agree, but be sure you are clear on what you need and patient.
Looking forward to seeing the machine in action.
Re: Output Control Both Auto and Manual < Acorn tech support review >
Posted: Thu Dec 05, 2019 9:04 am
by Viani86
Hello friends,
I also have this question about using an aux to open and close the pneumatic chuck after the M00. If I use the functions M61 (open chuck) and M62 (open chuck) in the program in automatic it works correctly. Now if you use the keyboard shortcut (aux) this will terminate the program. waiting for new start and back at the beginning of the program.
Thank you