Does the probe input on the Acorn have a contact debounce filter built in?
I ask this because Renishaw mentions this in some of their literature and that accuracy is improved if you can filter out the bounce that is present in a kienmatic probe output. Here is a sketch that describes what I'm talking about:
I also found a white paper on Renishaws site that has a good discussion of how a kinematic touch probe works.
Touch Probe Signal Debounce
Moderator: cnckeith
-
- Posts: 119
- Joined: Wed Aug 02, 2017 8:40 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: B0D5CC56DD75-0605170063 , 985DAD4295CF-0928170127 , 38D2694E4703-1222170401
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Near Guilford College, Greensboro, NC
- Contact:
-
- Posts: 7313
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Touch Probe Signal Debounce
Yes. It's all taken care of.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 119
- Joined: Wed Aug 02, 2017 8:40 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: B0D5CC56DD75-0605170063 , 985DAD4295CF-0928170127 , 38D2694E4703-1222170401
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Near Guilford College, Greensboro, NC
- Contact:
Re: Touch Probe Signal Debounce
Hi Keith,
Thanks for the very quick answer regarding this. Can the ACORN perform the same probing as shown in this video?
https://www.youtube.com/watch?v=IcVv1So1n_8
I suspect that if the answer is "yes" then I'd have to get Centroid Ultimate CNC software.
Thanks for the very quick answer regarding this. Can the ACORN perform the same probing as shown in this video?
https://www.youtube.com/watch?v=IcVv1So1n_8
I suspect that if the answer is "yes" then I'd have to get Centroid Ultimate CNC software.
Last edited by 762x51 on Mon Nov 13, 2017 5:35 pm, edited 1 time in total.
-
- Posts: 7313
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Touch Probe Signal Debounce
yes
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html