Page 2 of 3
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 7:37 am
by diycncscott
I'll look into it. You should not be receiving that message as your report indicates you definitely have Pro.
I apologize for the inconvenience.
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 1:48 pm
by cut2cut
diycncscott wrote: ↑Thu Feb 15, 2018 7:37 am
I'll look into it. You should not be receiving that message as your report indicates you definitely have Pro.
I apologize for the inconvenience.
I haven't connected my computer to the internet since before I started using the software. Perhaps this is an issue ?
Jake
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 2:19 pm
by diycncscott
No it isn't. Please pm me with your email
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 4:57 pm
by cut2cut
diycncscott wrote: ↑Thu Feb 15, 2018 7:37 am
I'll look into it. You should not be receiving that message as your report indicates you definitely have Pro.
I apologize for the inconvenience.
Perhaps I can narrow the error down to one of the parameters changes tonight. Previously I had tried rigid tapping but only changing , I believe, 78 and maybe perhaps 36 too, I don't recall, but I didn't see the error until I made further changes to the many parameters suggested in the draft document ? The draft document for rigid tapping suggests changing parameters 36,37,68,69,74,78,82,84,240,241,149. So through trial and error I can go through those to put them back to their original settings which I should have from a previous report file.
Jake
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 5:08 pm
by martyscncgarage
cut2cut wrote: ↑Thu Feb 15, 2018 4:57 pm
diycncscott wrote: ↑Thu Feb 15, 2018 7:37 am
I'll look into it. You should not be receiving that message as your report indicates you definitely have Pro.
I apologize for the inconvenience.
Perhaps I can narrow the error down to one of the parameters changes tonight. Previously I had tried rigid tapping but only changing , I believe, 78 and maybe perhaps 36 too, I don't recall, but I didn't see the error until I made further changes to the many parameters suggested in the draft document ? The draft document for rigid tapping suggests changing parameters 36,37,68,69,74,78,82,84,240,241,149. So through trial and error I can go through those to put them back to their original settings which I should have from a previous report file.
Jake
Did you send Scott a PM (private message) with your email address?
Click on his name and it should take you to that window.
Marty
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 5:14 pm
by cut2cut
[/quote]
Did you send Scott a PM (private message) with your email address?
Click on his name and it should take you to that window.
Marty
[/quote]
Yes, thanks Marty. I have. Perhaps he will figure it out before I try the above. I was just giving more details to work with. So far I haven't received an email.. he is probably looking for a solution, still.
Best Regards,
Jake
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 5:16 pm
by martyscncgarage
cut2cut wrote: ↑Thu Feb 15, 2018 5:14 pm
Did you send Scott a PM (private message) with your email address?
Click on his name and it should take you to that window.
Marty
[/quote]
Yes, thanks Marty. I have. Perhaps he will figure it out before I try the above. I was just giving more details to work with. So far I haven't received an email.. he is probably looking for a solution, still.
Best Regards,
Jake
[/quote]
Scott starts super early and leaves early. You may hear from him tomorrow. He is worth being patient and waiting for direction from.
Marty
Re: Rigid Tapping parameter 78 ?
Posted: Thu Feb 15, 2018 5:57 pm
by cut2cut
Scott starts super early and leaves early. You may hear from him tomorrow. He is worth being patient and waiting for direction from.
Marty
[/quote]
Thanks for the heads-up regarding his schedule . btw, I believe he asked for my email so he could fix a different issue I was having with my account here on the forum. I had asked a moderator and now notifications are working properly since I sent the email address.
Cheers,
Jake
Re: Rigid Tapping parameter 78 ?
Posted: Mon Feb 19, 2018 1:47 pm
by axmem
Hi there.
I have exactly same issue. Does anybody know how to get it sorted?
Re: Rigid Tapping parameter 78 ?
Posted: Mon Feb 19, 2018 1:56 pm
by diycncscott
Working on it. Send me a pm with email.