cnc 4 to acorn wiring
Moderator: cnckeith
-
- Posts: 5
- Joined: Wed May 16, 2018 9:13 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: cnc4-md3-10-80v serial#1872
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
cnc 4 to acorn wiring
Hey guys received my acorn board today, have a question about wiring from micro1 input header to acorn ? Does pulse go to step , dir to dr , pwr to com , cpugnd to en. If not let me know the right wiring diagram. Thanks
-
- Posts: 286
- Joined: Thu Mar 18, 2010 2:24 pm
Re: cnc 4 to acorn wiring
The connections would be below.
MICRO1 --> ACORN
PULSE --> ST
DIR --> DR
PWR --> EN
CPUVCC --> +5V
CPUGND --> COM
Remember that since those terminals on the ACORN are open-collector, you are going to want a pull-up resistor installed between those ACORN outputs and +5V. I would recommend either a 330 ohm resistor.
MICRO1 --> ACORN
PULSE --> ST
DIR --> DR
PWR --> EN
CPUVCC --> +5V
CPUGND --> COM
Remember that since those terminals on the ACORN are open-collector, you are going to want a pull-up resistor installed between those ACORN outputs and +5V. I would recommend either a 330 ohm resistor.
When requesting support, please ALWAYS post a current report. Find out how to take a report from your Acorn, CNC11 or CNC10 system here: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
If your question is PLC, Macro or program related, please also post a copy of the program or macro as well.
Without the above information we may not be able to help and/or reply until the required information is posted..
If your question is PLC, Macro or program related, please also post a copy of the program or macro as well.
Without the above information we may not be able to help and/or reply until the required information is posted..
-
- Posts: 5
- Joined: Wed May 16, 2018 9:13 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: cnc4-md3-10-80v serial#1872
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: cnc 4 to acorn wiring
Thanks again.
-
- Posts: 104
- Joined: Mon Mar 03, 2014 4:24 pm
- Allin1DC CNC Controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: cnc 4 to acorn wiring
Here is the schematic for Acorn to Micro1 drive.
- Attachments
-
- S14910-ACORN_rev3, CENTROID CNC4 MICRO1 DRIVE.pdf
- (91.7 KiB) Downloaded 132 times
When requesting support READ THIS POST first. viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)