New AjaxCNC Tech Bulletins added 3-18-13

_______________________________________________________














LOGIN below to POST your questions and comments on AjaxCNC products.

Moderator: cnckeith

Post Reply
cnckeith
Posts: 602
Joined: Wed Mar 03, 2010 4:23 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: Yes
CNC11: Yes
CPU10 or CPU7: Yes
System Serial Number: none
Contact:

New AjaxCNC Tech Bulletins added 3-18-13

Post by cnckeith » Mon Mar 18, 2013 4:19 pm

fyi... several new Tech Bulletins have been added to the AjaxCNC covering PC requirements, new voltage ratings on our Servo drives (now up to 180 volts!) and other good installation information..

http://www.ajaxcnc.com/ajax-technical-bulletins/
Attachments
ajaxtbs.JPG

tblough
Posts: 131
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: No
CNC11: Yes
CPU10 or CPU7: No
System Serial Number: 100505
100327
102696
Location: Boston, MA
Contact:

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by tblough » Wed Jan 25, 2017 1:14 pm

Is there an updated list somewhere? This stops back in 2013 and I have TSB 296 on setting up a spindle load meter so there are quite a few missing.

Thanks,


Tom
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.

cnckeith
Posts: 602
Joined: Wed Mar 03, 2010 4:23 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: Yes
CNC11: Yes
CPU10 or CPU7: Yes
System Serial Number: none
Contact:

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by cnckeith » Tue Feb 07, 2017 5:33 pm

tom, hello. the tech bulletins have been getting updated. just the date on the ajax web page was not being updated when the tb was updated but the link still would take you to the latest TB. and i've asked liviu to update the list thanks for pointing this out. we are working on a new "Centroid DIY" web page that will replace the ajaxcnc.com web page that will make things easier for everyone.
in the mean time here are direct links to

tb 296 load meter
http://www.centroidcnc.com/dealersuppor ... ds/296.pdf

tb 295 sigma 1 and 2
http://www.centroidcnc.com/dealersuppor ... ds/295.pdf

tb 292 installing a scale for dro use
http://www.centroidcnc.com/dealersuppor ... ds/292.pdf

289 soft travel limits
http://www.centroidcnc.com/dealersuppor ... ds/289.pdf

288 allin1dc settings for 3rd party servos
http://www.centroidcnc.com/dealersuppor ... ds/288.pdf

286 trouble shooting drive motor voltage supply
http://www.centroidcnc.com/dealersuppor ... ds/286.pdf

285 motor doesn't move no error, no fault
http://www.centroidcnc.com/dealersuppor ... ds/285.pdf

283 tweaking windows 8 for cnc control use
http://www.centroidcnc.com/dealersuppor ... ds/283.pdf

281 encoders not couting, dro does not update
http://www.centroidcnc.com/dealersuppor ... ds/281.pdf

278 setting up a Control Techniques SP spindle drive
http://www.centroidcnc.com/dealersuppor ... ds/278.pdf















Best regards, Keith

cnckeith
Posts: 602
Joined: Wed Mar 03, 2010 4:23 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: Yes
CNC11: Yes
CPU10 or CPU7: Yes
System Serial Number: none
Contact:

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by cnckeith » Wed Feb 08, 2017 10:34 am

ajax tech bulletin page has been updated.
http://www.ajaxcnc.com/ajax-technical-bulletins/

tblough
Posts: 131
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: No
CNC11: Yes
CPU10 or CPU7: No
System Serial Number: 100505
100327
102696
Location: Boston, MA
Contact:

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by tblough » Fri Feb 10, 2017 2:17 pm

Thanks, Keith. Can't wait to see the new Centroid DIY website. My Oak board should be here soon and I'm looking forward to jumping in.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.

Sportbikeryder
Posts: 23
Joined: Thu Jan 26, 2017 11:45 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC11: No
CPU10 or CPU7: Yes
System Serial Number: TBD when back at shop
Location: North Carolina

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by Sportbikeryder » Wed Mar 01, 2017 7:26 pm

Hmmm....the spindle load meter just gave me an idea. I'll have to check the vfd specs in the cabinet. The system is cnc10, but if it has an analog output on the vfd no reason I couldn't add a separate indicator somewhere. 8-)

cnckeith
Posts: 602
Joined: Wed Mar 03, 2010 4:23 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: Yes
CNC11: Yes
CPU10 or CPU7: Yes
System Serial Number: none
Contact:

Re: New AjaxCNC Tech Bulletins added 3-18-13

Post by cnckeith » Wed Mar 01, 2017 7:35 pm

yeah. you can always buy a little analog volt meter and use the analog output of the VFD to run the meter. check your vfd, often its 0-2 volts vdc output for load... so just buy a volt meter in that range.. and wa la you have a spindle load meter the old fashion way.

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests