Search found 153 matches
- Tue Oct 02, 2018 5:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
No was going to send back the drives and they sent me the new wiring diagram and there notes what has to be changed. Will go out and check with drives inverted and change to NC. i will let you know. I thought I had crazy power going to the T4 control power but it was a bad meter. frickin junk harbor...
- Tue Oct 02, 2018 4:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Where to set the acorn pulse frequency
- Replies: 7
- Views: 2690
Re: Where to set the acorn pulse frequency
just just checked the power going to the drive i have hooked up in T4 control power it goes from 90V to 313v and anywhere between and really quick just keeps bouncing.
. The T4 logic power is spot on 232V that line has a filter on.
. The T4 logic power is spot on 232V that line has a filter on.
- Tue Oct 02, 2018 4:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Where to set the acorn pulse frequency
- Replies: 7
- Views: 2690
Re: Where to set the acorn pulse frequency
I was looking for kHz
- Tue Oct 02, 2018 4:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Where to set the acorn pulse frequency
- Replies: 7
- Views: 2690
Re: Where to set the acorn pulse frequency
Not on my screen.
- Tue Oct 02, 2018 3:53 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
Thanks Marty, I did try what they sent me. They want the DYN4 drive enable to ACTIVE LOW. I emailed them back dont know where that is (well i cannot find it on the software screen) .and they want the acorn set to 400kHz, have no clue where that is. I have it wired just as your drawing you sent. Same...
- Tue Oct 02, 2018 3:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Where to set the acorn pulse frequency
- Replies: 7
- Views: 2690
Where to set the acorn pulse frequency
Where would you find to set the acorn pulse frequency to 400 kHz.
- Tue Oct 02, 2018 2:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
Well DMM just sent me there latest and greatest wiring diagram. YOU DO NOT INVERT ENABLE had drives packed up to ship back well will try again.
- Mon Oct 01, 2018 10:44 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
I wired them as per there drawing. it is only 220 single phase, even thou I do have 220 three phase here. Wanted to have single phase just encase I want to take it to the farm when I start adding to the railroad. I ordered them in December last year and got them in February. They were waiting on a n...
- Mon Oct 01, 2018 9:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
Well took the drives out of the cabinet, and one servo off the machine. Went and got a DB25 cable and wired it correctly to the other acorn on the bench. still dont work the DRIVES are BAD. They will be at UPS tomorrow to go back. What a waste of time.
- Mon Oct 01, 2018 4:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring which one
- Replies: 47
- Views: 14315
Re: Wiring which one
OK So disconnecting the Enable lines from Acorn made no difference? No difference at all Reconnect Enable lines to Acorn. I did that Can you please start up CNC 12. DID that See if rotors are locked. yes all three are locked If so, then press F3 MDI, the MDI input bar should appear. yes it does Chec...