Search found 9914 matches
- Mon Jan 01, 2024 4:10 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: New Project! (Chevalier bed mill, Allin1DC retrofit)
- Replies: 27
- Views: 7216
Re: New Project!
With an Allin1DC, you do not need the tachometers or their wires. I would keep the transformer, and either connect a Centroid CAPBRDLO rectifier assembly to the 100VAC secondary; or keep the original Chevalier rectifier assembly (bridge, cap, and resistor) likewise connected to that 100VAC secondar...
- Sat Dec 30, 2023 10:33 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: New Project! (Chevalier bed mill, Allin1DC retrofit)
- Replies: 27
- Views: 7216
Re: New Project!
Took a new job so was put on back burner, But back on it, Finally. So going through got wired up to the actual servos. The machine has a transformer, pic attached. Not sure if it would be worth it to use. Unfortunately, in my knowledge 220v consists of 2 hot leads i assume 230v does as well but the...
- Thu Dec 07, 2023 7:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
You can use the DB25 cable with flying leads. Provided you connect the leads CORRECTLY Suggest you make a small spreadsheet or chart with the DB25 pin number and color and match it to the Acorn Function on its DB25 and then a column to where you will land those wires on the drives. To make sure you...
- Thu Dec 07, 2023 7:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
You can use the DB25 cable with flying leads. Provided you connect the leads CORRECTLY Suggest you make a small spreadsheet or chart with the DB25 pin number and color and match it to the Acorn Function on its DB25 and then a column to where you will land those wires on the drives. To make sure you ...
- Thu Dec 07, 2023 7:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
Marty and Keith are correct, those stepper drives need to be wired to the DB25 to work reliably. You need a breakout board and the drives wire to it. Here's a link to a breakout board from Amazon. https://www.amazon.com/gp/product/B073RG3GG6/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&...
- Thu Dec 07, 2023 7:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
You bet heres a link to the driver https://www.wantmotor.com/closed-loop-stepper-motor-driver/ss880-servo-driver.html Here is a link to the manual: https://www.hobbytronics.co.za/Content/external/1174/SS880%20programme.pdf I would wire DB25 STEP1 to driver +Pulse DB25 DIRECTION 1 to driver +Dir DB2...
- Thu Dec 07, 2023 6:50 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
Can you PLEASE post a picture or make and model of your drives? And or a link to its manual so we can better make a suggestion.
I gave an example of a schematic. you may NOT need an external power supply. Until we know exactly the make and model drive you are using, can't help you much more.
I gave an example of a schematic. you may NOT need an external power supply. Until we know exactly the make and model drive you are using, can't help you much more.
- Thu Dec 07, 2023 5:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: x-x+ jogging moves in the same direction in the x- direction <resovled>
- Replies: 74
- Views: 19016
Re: x-x+ jogging moves in the same direction in the x- direction <resovled>
Keith is correct look at this schematic as an example: https://www.centroidcnc.com/dealersupport/schematics/uploads/s15207.r1.pdf If you are going to rewire the control, get a DB25 male breakout board from Amazon and start fresh. You should REALLY be posting the make and model of the drives along wi...
- Thu Nov 30, 2023 5:13 pm
- Forum: Success Stories
- Topic: Custom Centroid APi CNC12 screen set by Adam for a custom CNC machine
- Replies: 1
- Views: 2204
Re: Custom Centroid APi CNC12 screen set by Adam for a custom CNC machine
Very nice work. Interesting and shows the power of the Centroid control
Marty
Marty
- Mon Nov 27, 2023 2:27 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Conecting old fanuc dc drive
- Replies: 24
- Views: 9895
Re: Conecting old fanuc dc drive
Hello Marty I'm Rafael Almanzar, a while ago we talked about the use of old Fanuc drives to be able to connect them with the centroid oak control And searching on the centroid page I found the article TB 233 (REV 1) Where it explains the connection of these old drives to the oak control and the 5M ...