Search found 114 matches
- Sat Dec 23, 2017 4:39 pm
- Forum: Acorn CNC Tech Tips Knowledge Base, Look Here! before posting
- Topic: Encoder Basics
- Replies: 50
- Views: 86358
Re: Encoder Basics
Yes exactly where I read that. Thanks for posting link.
- Sat Dec 23, 2017 2:43 am
- Forum: Acorn CNC Tech Tips Knowledge Base, Look Here! before posting
- Topic: Encoder Basics
- Replies: 50
- Views: 86358
Re: Encoder Basics
I am new to encoding terminology. I found the below passage helpful in understanding CPR and PPR. CPR most commonly stands for Counts per Revolution, and refers to the number of quadrature decoded states that exist between the two outputs A and B. With both outputs A and B switching between high and...
- Wed May 21, 2014 8:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: vfd drive
- Replies: 3
- Views: 2799
Re: vfd drive
Have you measured the voltage on each leg of your RPC? Is it balanced? If not and with only 2-3hp need probably I would not risk using the wild leg on the VFD input as there is no real benefit. In fact it will cost you more per kw as the ideler is running during usage of the RPC.
- Mon May 19, 2014 9:56 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: KB electronics VFD wiring help
- Replies: 2
- Views: 2044
Re: KB electronics VFD wiring help
So post up the info for others.
- Sun May 18, 2014 9:08 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: offline centroid programming
- Replies: 1
- Views: 1707
Re: offline centroid programming
Request the USB key.
- Thu May 08, 2014 1:39 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Can I Add, and how: a functional geometry wear table option?
- Replies: 2
- Views: 1930
Re: Can I Add, and how: a functional geometry wear table opt
Why not create a second tool adding the additional test diameter to the tool definition?
- Sun Apr 27, 2014 8:06 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: AJAX CONTROL CHANGE OVER
- Replies: 4
- Views: 2920
Re: AJAX CONTROL CHANGE OVER
Check the amperage setting for the drive inputs (the pins have a range). Once you verify those are right make sure to run the tuning.
More Knowledgeable people than I will reply tomorrow
More Knowledgeable people than I will reply tomorrow
- Fri Apr 25, 2014 9:25 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Ajax reverse tapping cycle
- Replies: 6
- Views: 4065
Re: Ajax reverse tapping cycle
OK I have a ER32 floating tapping head now and the DC regen res installed for braking my VFD.
Is there a formula or table for figuring out good speeds for taps? 1/4-20, 1/2-13. 4-40, 8-32, 10 - those are the sizes I use the most.
Any advice on using the floating tapping heads?
Is there a formula or table for figuring out good speeds for taps? 1/4-20, 1/2-13. 4-40, 8-32, 10 - those are the sizes I use the most.
Any advice on using the floating tapping heads?
- Thu Apr 17, 2014 4:42 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Centroid CNC12, CNC11 & CNC10 Manuals
- Replies: 20
- Views: 62180
Re: Circuit Board Manuals, Install Manuals, Operator Manuals
Centroid Rotary Table - RT-150
- Sun Apr 06, 2014 11:08 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: GS2-XXXX ALLIN1DC
- Replies: 4
- Views: 3054
Re: GS2-XXXX ALLIN1DC
Would it help to see the Hitachi WJ200 2.2kw connections to the AllInOneDC?