Search found 428 matches

by Centroid_Liviu
Fri Jan 10, 2014 3:48 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Power Supply Question
Replies: 7
Views: 3667

Re: Power Supply Question

Our 110VAC Power supply kit will output 110VDC. There should probably be no issue using it with your servos. Worst case scenario you will lose a few RPM at the top end. I have attached a full wiring schematic.
by Centroid_Liviu
Fri Jan 10, 2014 11:22 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Power Supply Question
Replies: 7
Views: 3667

Re: Power Supply Question

It would depend on what the capacitor/rectifier is rated at. The ALLIN1DC can handle up to 180VDC coming in for its DC drives. I have attached a schematic showing a setup with our 110VAC power supply kit.
by Centroid_Liviu
Thu Jan 09, 2014 9:03 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Dual MPG / hand wheels on retrofit lathe
Replies: 2
Views: 2078

Re: Dual MPG / hand wheels on retrofit lathe

Our controls support the use of Dual Handwheels, allowing you manual control of your axis while still keeping track of your position in the software. I have attached a simple wiring hook-up below. Do not think of the dual handwheel as an MPG since the MPG typically has an axis selector switch and a ...
by Centroid_Liviu
Thu Jan 09, 2014 8:44 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Keyboard bounce
Replies: 4
Views: 2506

Re: Keyboard bounce

Do you have the serial numbers for those controls? Or if you can take a picture of them and post them here. Several different models of keypads have used over the years.
by Centroid_Liviu
Wed Jan 08, 2014 2:12 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Bench top testing
Replies: 1
Views: 1222

Re: Bench top testing

Can you please send us a report of your system to tech@ajaxcnc.com . From the main menu press F7-Utilties, F7-Report, and choose where you wish to save the file. We would just need the report.zip file created. The report file will allow tech support to see all of your parameters, settings, and any f...
by Centroid_Liviu
Wed Jan 08, 2014 2:10 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Knee mill Low gear reversing on VFD
Replies: 8
Views: 5213

Re: Knee mill Low gear reversing on VFD

Please follow the table below to connect the Hitachi WJ200-015SF drive to the ALLIN1DC. Make sure that there is a jumper installed between pins L and PLC on the inverter. The 0-10VDC COM signal must be connected to the L that is in between the OI and AM pins on the inverter. Make sure that A001 is s...
by Centroid_Liviu
Wed Jan 08, 2014 2:07 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Add 4th axis
Replies: 4
Views: 2175

Re: Add 4th axis

You can update to the latest version of CNC10 2.72, but the computer specs will also have to be updated. The software and instructions and PC minimum specs can be found here : http://www.ajaxcnc.com/ajax-cnc-legacy-software/ . Or if you prefer we can send you a brand new Flash Card (with the latest ...
by Centroid_Liviu
Mon Dec 16, 2013 1:18 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: ALLIN1DC Motion Controller and Brushless DC Servos?
Replies: 1
Views: 1208

Re: ALLIN1DC Motion Controller and Brushless DC Servos?

There is some confusion as to what makes a DC servo, DC brush-less servo and AC servo. Without getting into the technical specifics the ALLIN1DC should be able to handle DC "brushed" servos up to 40 in-lb /4.52 NM, 180V, 15 amps. A lot of DC servos simply say "DC Servomotor", and...
by Centroid_Liviu
Tue Dec 10, 2013 9:10 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Appendix A & B of ALLIN1DC Installation Manual
Replies: 14
Views: 6488

Re: Appendix A & B of ALLIN1DC Installation Manual

The install manuals, operators manuals, and schematics are all included on the CD that ships out with every order (as well as on the Ajax website). We are currently in the process of updating the install manuals to make them more user friendly, especially in regards to tuning. In the mean-time if yo...
by Centroid_Liviu
Mon Dec 09, 2013 12:41 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Communication Fault error
Replies: 5
Views: 3118

Re: Communication Fault error

Please send a report from your system to tech@ajaxcnc.com . From the main menu press F7-Utilities, F7-Report. We would just need the report.zip created. The report will allow tech support to see what your parameters settings are at, all the faults you are getting, and any other settings. With that i...