Search found 9914 matches
- Thu Nov 04, 2021 9:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: C86ACCP board green light comes on5 sec goes off (Self resolved )
- Replies: 8
- Views: 1684
Re: C86ACCP board green light comes on5 sec goes off (Self resolved )
Hi Marty, What I found is this site has two version for setting up clearpath motors using the C86ACCP. I accidentally came across it when I threw the paper version I had printed down onto my laptop. The two drawing were different if you look at the picture on the original post you will see " D...
- Tue Nov 02, 2021 10:56 pm
- Forum: Acorn CNC Plasma
- Topic: Phoenix 2x2 Router fitted with CNC Plasma
- Replies: 15
- Views: 3086
Re: Phoenix 2x2 Router fitted with CNC Plasma
hear is a reply from jim colt on the prime weld plasma Jim Colt While there are not any good pics of the torch and nozzle that I can find…..the drawings of the torch look like a copy of a 30 year old Max40 unshielded torch nozzle design. Hypertherm has had at least 3 torch design upgrades since the...
- Tue Nov 02, 2021 10:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3419
Re: Novakon Torus pro, Servo motor axis config. .850" off over 4"
Section 7.3 of the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
https://www.centroidcnc.com/centroid_di ... manual.pdf
- Tue Nov 02, 2021 9:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3419
Re: Novakon Torus pro, Servo motor axis config. .850" off over 4"
Have you run the DRO fine tuning?
It's your machine and your call....
It's your machine and your call....
- Tue Nov 02, 2021 9:15 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3419
Re: Novakon Torus pro, Servo motor axis config. .850" off over 4"
You probably don't have the drive setup correctly. Possibly you have a bad value in gearing.
You really should contact the vendor that sold you the drives for guidance.
You really should contact the vendor that sold you the drives for guidance.
- Tue Nov 02, 2021 4:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Novakon Torus pro, Servo motor axis config. .850" off over 4"
- Replies: 16
- Views: 3419
Re: Novakon Torus pro, Servo motor axis config. .850" off over 4"
Your noise is gone. ALWAYS use a shielded cable If your ballscrew pitch is 5.08turns per inch, screw direct driven by the servo, then set the Overall Turns Ratio that way. (5.08) You have a 2500 count encoder, set the Step/Revolution to 10,000 (2500x4 in quadrature, please read your manual, specific...
- Tue Nov 02, 2021 10:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: MAS VXR 50 to CNC
- Replies: 3
- Views: 843
Re: MAS VXR 50 to CNC
Your pictures don't give much detail but the one picture of an axis motor seems to indicate it may likely be a DC Brush Servo, might have an encoder. You have to definitively ascertain what kind of axis motors you have and whether or not you want to reuse them. Are you wanting to try and reuse the t...
- Tue Nov 02, 2021 10:50 am
- Forum: Centroid Acorn CNC Controller
- Topic: ATC and VFDEnable
- Replies: 33
- Views: 8869
Re: ATC and VFDEnable
Might be tough, but try TVT American. Very well made and multiple configurations
http://www.tvtamerica.com/Metric-AC-Mot ... e-atex.htm
I would look for the correct bolt pattern/rpm/mounting arrangement
http://www.tvtamerica.com/Metric-AC-Mot ... e-atex.htm
I would look for the correct bolt pattern/rpm/mounting arrangement
- Tue Nov 02, 2021 10:45 am
- Forum: Centroid Acorn CNC Controller
- Topic: C86ACCP board green light comes on5 sec goes off (Self resolved )
- Replies: 8
- Views: 1684
- Tue Nov 02, 2021 10:33 am
- Forum: Centroid Acorn CNC Controller
- Topic: Need help with wiring
- Replies: 6
- Views: 1465
Re: Need help with wiring
Please take the time to follow this post: https://centroidcncforum.com/viewtopic.php?f=60&t=1043 The more information you can provide, the better suggestions we can make. Have you read the Acorn installation manual? https://www.centroidcnc.com/centroid_diy/downloads/acorn_documentation/centroid_...