Search found 33 matches
- Tue Aug 01, 2017 8:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 100 Step MPG - reverse dial direction
- Replies: 7
- Views: 2628
Re: 100 Step MPG - reverse dial direction
Whoop's! ..just noticed the new Allin1dc manual shows two different ways to wire up the MGP - check out the A/A+/B/B+ connector pin locations on page ~115 ( the ALLINONEDC Cables Schematic) - then compare it to the ALLINONEDC Connectors on page ~139 so.. which is the right way - so I can reverse it ...
- Mon Jul 17, 2017 7:44 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Messages during ALLIN1DC Bench Test
- Replies: 4
- Views: 2538
- Sun Jul 16, 2017 7:21 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Messages during ALLIN1DC Bench Test
- Replies: 4
- Views: 2538
Messages during ALLIN1DC Bench Test
Hi Gang! I'm just starting the Bench Test of the AllIN1DC - going through the paces and getting a couple of messages along the way: The first one: 5161 Unconfigured Mini PLC 1 Found I have a PLCADD1616 in the mix so not sure it that's generating the message, or if the message is part of the normal p...
- Sat Jun 10, 2017 9:10 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 100 Step MPG - reverse dial direction
- Replies: 7
- Views: 2628
Re: 100 Step MPG - reverse dial direction
Thanks, I'll give the A>B and A/->B/ swap a try see how it works.
Jay
Jay
- Tue Jun 06, 2017 11:16 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 100 Step MPG - reverse dial direction
- Replies: 7
- Views: 2628
100 Step MPG - reverse dial direction
Hi, This may be an 'out in left field' question, but is there way to reverse the dial direction on the Ajax supplied MPG. My Bridgeport S2I2 has jog sticks and a matching MPG that mimic table movement rather than head movement. The MPG of which to be replaced by the Ajax 100-step MPG. However the ol...
- Wed May 24, 2017 10:44 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Bridgeport Series 2 Interact II - Spindle Override Dial
- Replies: 2
- Views: 1353
Re: Bridgeport Series 2 Interact II - Spindle Override Dial
Great - that all makes good sense. I'll have to look around at what I've got for VDC - likely 12VDC - to keep my voltage up where I can. I do have an M39 Pendant so some redundancy in controls, but I think the Interact idea was if you're going manual - your working more from the head, joysticks and ...
- Wed May 24, 2017 5:59 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Bridgeport Series 2 Interact II - Spindle Override Dial
- Replies: 2
- Views: 1353
Bridgeport Series 2 Interact II - Spindle Override Dial
Hi, I'm finally getting my Bridgeport Series 2 Interact II together and converted over to CNC11 - have to admit doing this puts me in my happy place. I'm planning on keeping inline with the Interact philosophy. Thus keeping the X/Y/Z jog joysticks and rapid buttons, but will dump the OEM MPG for the...
- Wed Jan 07, 2015 12:12 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Quencharc
- Replies: 2
- Views: 2416
Quencharc
Hi, I'm working on my Bridgeport S2I2 upgrade and found my contactors are all 110vac coils - so I'm planning on using 110vac on the E-Stop and Flood Pump coil circuits. I do have a few questions: 1. From what I can read it appears the AllinOne is rated for the 110vac E-Stop and Flood pump circuit on...
- Wed Dec 17, 2014 7:10 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle Motor for Bridgeport Series 2 Interact II
- Replies: 5
- Views: 4147
Re: Spindle Motor for Bridgeport Series 2 Interact II
Thanks ..good advice!
- Fri Dec 05, 2014 10:40 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle Motor for Bridgeport Series 2 Interact II
- Replies: 5
- Views: 4147
Re: Spindle Motor for Bridgeport Series 2 Interact II
I just found this motor on Ebay and wondering if it's a true 3 HP - or if it's worth my while or not to change it out http://www.ebay.com/itm/3-HP-REPLACEMENT-MOTOR-FOR-BRIDGEPORT-MILL-MILLING-MACHINE-MYC0A-1550001-2550019-/161387892450?pt=BI_Heavy_Equipment_Parts&hash=item259377cee2 Thanks Jay