Search found 286 matches
- Fri Jun 15, 2018 12:05 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Encoder connectors
- Replies: 4
- Views: 2524
Re: Encoder connectors
The 9-pin single row connector https://www.digikey.com/product-detail/ ... -ND/115047 and the pins https://www.digikey.com/product-detail/ ... /WM2512-ND.
- Thu Jun 14, 2018 9:09 am
- Forum: Centroid Acorn CNC Controller
- Topic: custom macro help (Resolved)
- Replies: 20
- Views: 7987
Re: custom macro help
The logic that I have written works as I just tested it. The only difference is that I did not have the # symbol when defining the input after the P designator.
- Thu Jun 14, 2018 8:58 am
- Forum: Centroid Acorn CNC Controller
- Topic: Thermwood C53 5x10 Retrofit
- Replies: 18
- Views: 6950
Re: Thermwood C53 5x10 Retrofit
The cncm.hom file in the report that you attached has no logic in it to square the table. What's odd is that there is logic in that file that sets certain local variables but the variables aren't used anywhere in that file. I would recommend starting with the cncm.hom file that cnckeith posted which...
- Wed Jun 13, 2018 2:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ATC Macro / PLC Help please <success!>
- Replies: 85
- Views: 45641
Re: ATC Macro / PLC Help please <success!>
Unfortunately, there isn't. The only way around this issue that I can think of is the way that you have already determined using the M0.
- Wed Jun 13, 2018 2:47 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: another schematic please
- Replies: 3
- Views: 2354
Re: another schematic please
Sorry about that. I can't find a schematic that shipped out with that particular PLC program but you should be able to use the attached schematic as a guide.
- Wed Jun 13, 2018 12:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: another schematic please
- Replies: 3
- Views: 2354
Re: another schematic please
Here is the schematic associated with that PLC program.
- Wed Jun 13, 2018 12:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: custom macro help (Resolved)
- Replies: 20
- Views: 7987
Re: custom macro help
I apologize. I didn't read your first post properly. I believe that if you switch that input back to being NC in the wizard, it should work.
- Wed Jun 13, 2018 12:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ATC Macro / PLC Help please <success!>
- Replies: 85
- Views: 45641
Re: ATC Macro / PLC Help please <success!>
Our software department is looking into this. In the meantime, it appears that you have found a workaround by adding an M0.
- Tue Jun 12, 2018 1:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: custom macro help (Resolved)
- Replies: 20
- Views: 7987
Re: custom macro help
It appears that diycncscott got the P values reversed. When the P value is positive, the control is looking for the switch to open and when the P value is negative, the control is looking for the switch to close. Based on your original requirements, the M105/M106 logic in your program as well as the...
- Tue Jun 12, 2018 1:21 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Schematic
- Replies: 2
- Views: 2027
Re: Schematic
Here is the schematic that goes with that PLC program.