Search found 3137 matches
- Mon Apr 15, 2024 6:53 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: NPT + Threads in Intercon - Workflow
- Replies: 8
- Views: 730
Re: NPT + Threads in Intercon - Workflow
I cut 0-80 and M1 all the time. You need an extremely sharp tool and very small infeeds. As for cutting into your shoulder, where are you setting your Z0 for the threading tool. If you use the point of the tool, you'll have to reduce the ending Z by 1/2 the width of the tool. I set my Z0 to the side...
- Sat Apr 13, 2024 8:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: NPT + Threads in Intercon - Workflow
- Replies: 8
- Views: 730
Re: NPT Threads in Intercon - Workflow
The Centroid minor diameters are only valid for threading tools with the correct root flat or radius. If you are using a sharp V threading tool, you'll have to subtract another 0.108 * pitch from the minor diameter. You need to adjust the minor diameter in the thread details page and not the tool we...
- Thu Apr 11, 2024 4:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: AcornSix - Zri Homing with linear scales
- Replies: 22
- Views: 1609
Re: AcornSix - Zri Homing with linear scales
Just one point I'm sure you are aware of. The X-axis will not have an index pulse. The index pulse will be on whatever axis the SCALE is attached to.
- Tue Apr 09, 2024 3:23 pm
- Forum: Centroid Acorn CNC Controller
- Topic: AcornSix - Zri Homing with linear scales
- Replies: 22
- Views: 1609
Re: AcornSix - Zri Homing with linear scales
Those variables will only change when the encoder is sitting on the index mark. You will need to check the variable when the asterisk is showing on the PID screen.
- Tue Apr 09, 2024 11:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: DRO display units
- Replies: 6
- Views: 328
Re: DRO display units
I haven't tried recently, but in the past there were issues with DRO units different than machine units.
AFAIK, there is still no way to programmatically change DRO and machine units. The only way is from the config screen
AFAIK, there is still no way to programmatically change DRO and machine units. The only way is from the config screen
- Mon Apr 08, 2024 8:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: C Axis Lathe Situation
- Replies: 7
- Views: 358
Re: C Axis Lathe Situation
Leave the negative numbers and the C-axis out for a moment and restate what Marc said. If my X0 is in the center of the part, X-2.0 to X2.0 would be a 4" move to the right, while X2.0 to X-2.0 would be a 4" move to the left. I think this is what you are expecting: G00 X-2.000 G01 X2.000 G0...
- Sun Apr 07, 2024 7:01 am
- Forum: Centroid Acorn CNC Controller
- Topic: C Axis Lathe Situation
- Replies: 7
- Views: 358
Re: C Axis Lathe Situation
C-23 to C-60 would move CCW.
C-60 to C-23 would be CW.
Same thing happens on Z.
C-60 to C-23 would be CW.
Same thing happens on Z.
- Fri Apr 05, 2024 1:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 3 Phase DC Power Supply
- Replies: 1
- Views: 175
Re: 3 Phase DC Power Supply
208V 3Ø to 120V 1Ø transformers are readily available. All you need is the Centroid "capboard".
- Thu Apr 04, 2024 1:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't add negative number to Low Range Spindle Speed RatioRatio <milling machine as a lathe, resolved>
- Replies: 47
- Views: 1678
Re: Can't add negative number to Low Range Spindle Speed RatioRatio
1) Thread milling doesn't use the encoder, so that is why there are no problems with that. 2) Tapping on the mill will work fine in high and back gear. Peck tapping will not work in either. 3) Even if you get the "back gear" worked out in the lathe software, lathe threading in back gear wi...
- Thu Apr 04, 2024 11:28 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can't add negative number to Low Range Spindle Speed RatioRatio <milling machine as a lathe, resolved>
- Replies: 47
- Views: 1678
Re: Can't add negative number to Low Range Spindle Speed RatioRatio
Because that's exactly what it's designed to do. CNC12 changes the DAC output based on the gear ratio. The spindle encoder reads the SPINDLE speed and therefore should never need any gear ratio applied to it. It also does not, and SHOULD not, need to be "reversed" by a negative gear ratio....