Search found 428 matches
- Fri Jan 10, 2014 3:48 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Power Supply Question
- Replies: 7
- Views: 3717
Re: Power Supply Question
Our 110VAC Power supply kit will output 110VDC. There should probably be no issue using it with your servos. Worst case scenario you will lose a few RPM at the top end. I have attached a full wiring schematic.
- Fri Jan 10, 2014 11:22 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Power Supply Question
- Replies: 7
- Views: 3717
Re: Power Supply Question
It would depend on what the capacitor/rectifier is rated at. The ALLIN1DC can handle up to 180VDC coming in for its DC drives. I have attached a schematic showing a setup with our 110VAC power supply kit.
- Thu Jan 09, 2014 9:03 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Dual MPG / hand wheels on retrofit lathe
- Replies: 2
- Views: 2091
Re: Dual MPG / hand wheels on retrofit lathe
Our controls support the use of Dual Handwheels, allowing you manual control of your axis while still keeping track of your position in the software. I have attached a simple wiring hook-up below. Do not think of the dual handwheel as an MPG since the MPG typically has an axis selector switch and a ...
- Thu Jan 09, 2014 8:44 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Keyboard bounce
- Replies: 4
- Views: 2524
Re: Keyboard bounce
Do you have the serial numbers for those controls? Or if you can take a picture of them and post them here. Several different models of keypads have used over the years.
- Wed Jan 08, 2014 2:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Bench top testing
- Replies: 1
- Views: 1232
Re: Bench top testing
Can you please send us a report of your system to tech@ajaxcnc.com . From the main menu press F7-Utilties, F7-Report, and choose where you wish to save the file. We would just need the report.zip file created. The report file will allow tech support to see all of your parameters, settings, and any f...
- Wed Jan 08, 2014 2:10 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Knee mill Low gear reversing on VFD
- Replies: 8
- Views: 5294
Re: Knee mill Low gear reversing on VFD
Please follow the table below to connect the Hitachi WJ200-015SF drive to the ALLIN1DC. Make sure that there is a jumper installed between pins L and PLC on the inverter. The 0-10VDC COM signal must be connected to the L that is in between the OI and AM pins on the inverter. Make sure that A001 is s...
- Wed Jan 08, 2014 2:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Add 4th axis
- Replies: 4
- Views: 2194
Re: Add 4th axis
You can update to the latest version of CNC10 2.72, but the computer specs will also have to be updated. The software and instructions and PC minimum specs can be found here : http://www.ajaxcnc.com/ajax-cnc-legacy-software/ . Or if you prefer we can send you a brand new Flash Card (with the latest ...
- Mon Dec 16, 2013 1:18 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: ALLIN1DC Motion Controller and Brushless DC Servos?
- Replies: 1
- Views: 1218
Re: ALLIN1DC Motion Controller and Brushless DC Servos?
There is some confusion as to what makes a DC servo, DC brush-less servo and AC servo. Without getting into the technical specifics the ALLIN1DC should be able to handle DC "brushed" servos up to 40 in-lb /4.52 NM, 180V, 15 amps. A lot of DC servos simply say "DC Servomotor", and...
- Tue Dec 10, 2013 9:10 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Appendix A & B of ALLIN1DC Installation Manual
- Replies: 14
- Views: 6515
Re: Appendix A & B of ALLIN1DC Installation Manual
The install manuals, operators manuals, and schematics are all included on the CD that ships out with every order (as well as on the Ajax website). We are currently in the process of updating the install manuals to make them more user friendly, especially in regards to tuning. In the mean-time if yo...
- Mon Dec 09, 2013 12:41 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Communication Fault error
- Replies: 5
- Views: 3135
Re: Communication Fault error
Please send a report from your system to tech@ajaxcnc.com . From the main menu press F7-Utilities, F7-Report. We would just need the report.zip created. The report will allow tech support to see what your parameters settings are at, all the faults you are getting, and any other settings. With that i...