Search found 2190 matches
- Sun Jan 14, 2024 9:45 am
- Forum: Centroid Acorn CNC Controller
- Topic: Curious error msg for WMPG
- Replies: 6
- Views: 408
Re: Curious error msg for WMPG
Make sure in the power settings that "USB Suspend" is disabled
- Tue Jan 02, 2024 7:12 pm
- Forum: Buy, Sell, Trade
- Topic: SOLD!! 2.2kw (3hp) VFD (single phase input)
- Replies: 2
- Views: 7905
Re: SOLD!! 2.2kw (3hp) VFD (single phase input)
Items have been sold
- Sun Dec 24, 2023 12:26 am
- Forum: Centroid Acorn CNC Controller
- Topic: Touch Off Tool Question
- Replies: 9
- Views: 1319
Re: Touch Off Tool Question
If you have the input available, connect the over travel to a Z minus limit
- Wed Dec 20, 2023 11:47 am
- Forum: Buy, Sell, Trade
- Topic: SOLD!! 2.2kw (3hp) VFD (single phase input)
- Replies: 2
- Views: 7905
Re: 2.2kw (3hp) VFD (single phase input)
PRICE REDUCED!! $200 Each or both for $350 shipped CONUS
- Mon Dec 04, 2023 9:10 am
- Forum: Centroid Acorn CNC Controller
- Topic: Atc spins endlessly after reboot. <resolved>
- Replies: 8
- Views: 2282
Re: Atc spins endlessly after reboot.
If you have an axis designated to rotate the carousel, then CNC12 will attempt to home it via the wizard generated homing routine. With no sensor installed, the axis will rotate until the sensor triggers. If no sensor.......... If the position of the carousel is important, I recommend adding a homin...
- Sun Dec 03, 2023 4:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Atc spins endlessly after reboot. <resolved>
- Replies: 8
- Views: 2282
Re: Atc spins endlessly after reboot.
Does your carousel have a homing switch defined? It sounds like it is "driving by" the sensor
- Sat Dec 02, 2023 10:02 am
- Forum: Centroid Acorn CNC Controller
- Topic: E-stop config for router
- Replies: 17
- Views: 11961
Re: E-stop config for router
If the power supply LED is blinking, then you have a short in the 24vdc system. Your system will not runThe green LED on the Meanwell (power source) constantly blinks
- Fri Dec 01, 2023 3:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Gantry squaring - purely manual or CNC12-assisted?
- Replies: 13
- Views: 1668
Re: Gantry squaring - purely manual or CNC12-assisted?
Stepper motors and by extension step & direction DC servos may, in fact will, "jump" into a nearby magnetic detent on startup. Sometimes clockwise, sometimes counterclockwise. Sometimes a few encoder counts, sometimes more. I don't even know if stopping the motor at exactly the same sh...
- Thu Nov 23, 2023 10:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Hardware-paired Clearpath gantry servos falls out of step - resolved
- Replies: 19
- Views: 2894
Re: Hardware-paired Clearpath gantry servos fell out of step
This can also be caused by an incomplete or improper auto tune. Especially on dual motor axes
- Thu Nov 23, 2023 10:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can Clearpath SDSK & Hybrid Steppers be connected to C86ACCP ?
- Replies: 9
- Views: 1780
Re: Can Clearpath SDSK & Hybrid Steppers be connected to C86ACCP ?
#1: The C86ACCP is not compatible with the AcornSIX
#2: Both your ClearPaths and steppers will connect directly to the AcornSIX via flying leads into the terminal blocks
#3: Most stepper alarms will work with AcornSIX
#4: Are you sure that those <200ozin steppers are suitable for your mill?
#2: Both your ClearPaths and steppers will connect directly to the AcornSIX via flying leads into the terminal blocks
#3: Most stepper alarms will work with AcornSIX
#4: Are you sure that those <200ozin steppers are suitable for your mill?