******* update 4-10-24 *********v1.3.0 is now available.
fixed notepadd++ installation for Windows 11 changes
https://www.centroidcnc.com/centroid_di ... _1.3.0.zip
found on
https://www.centroidcnc.com/centroid_di ... loads.html
Search found 7292 matches
- Wed Apr 10, 2024 3:00 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: The Centroid CNC PC Tuner v1.3.0 has been released.
- Replies: 3
- Views: 10171
- Wed Apr 10, 2024 2:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: The Centroid CNC PC Tuner v1.3.0 has been released.
- Replies: 25
- Views: 26206
Re: The Centroid CNC PC Tuner v1.3.0 has been released.
******* update 4-10-24 *********v1.3.0 is now available.
fixed notepadd++ installation for Windows 11 changes
found on
https://www.centroidcnc.com/centroid_di ... loads.html
fixed notepadd++ installation for Windows 11 changes
found on
https://www.centroidcnc.com/centroid_di ... loads.html
- Wed Apr 10, 2024 2:29 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 v5.1 RC#5 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
- Replies: 12
- Views: 436
Re: CNC12 v5.1 RC#5 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
Added to the Wizard Touch Probe setup menu the ability to enable/disabled the new Probe Protection feature based on Tool number How would that work for the oak since no wizard is possible. Is the entry in the parameters enough? Yes, (the wizard sets cnc12 parameters). any new parameters will be add...
- Tue Apr 09, 2024 8:26 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 v5.1 RC#5 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
- Replies: 12
- Views: 436
CNC12 v5.1 RC#5 Mill, Lathe, Router, Plasma RC5 now available for download and testing.
CNC12 v5.1 RC#5 Mill, Lathe, Router, Plasma RC5 now available for download and testing. Models: Acorn, AcornSix, Hickory, Oak, Allin1DC, MPU11 Download link https://centroid-support.filemail.com/d/awgpjertgujoqmq Differences from RC4 - Added to the Wizard Tool Touch Off device setup menu choices bet...
- Tue Apr 09, 2024 7:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Coordinate display overlapping in graphing.
- Replies: 15
- Views: 473
Re: Coordinate display overlapping in graphing.
ok great! thanks for confirmationGary Campbell wrote: ↑Tue Apr 09, 2024 4:28 pm Thats what I get for AVID 20t on motor 64t on pulley 20t spur gear:
AVID.JPG
- Tue Apr 09, 2024 7:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: today i drafted a discussion paper on tool height offset methods
- Replies: 23
- Views: 1380
Re: today i drafted a discussion paper on tool height offset methods
rev3 attached.
I still need to incorporate all of your suggestions. thanks.
I still need to incorporate all of your suggestions. thanks.
- Tue Apr 09, 2024 3:30 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Centroid Operator Control Panel Interface Board: USB-BOB
- Replies: 25
- Views: 1001
Re: Centroid Operator Control Panel Interface Board: USB-BOB
Question about the ribbon cables: how long are they and can they be extended if they're short? I think I'll need about 5 feet of cable to run from the electronics box on the back of my lathe, then below it and up into the front control panel. If they're not long enough, what kind of connectors are ...
- Tue Apr 09, 2024 3:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build LMS 3990 Hi Torque Mini Mill
- Replies: 33
- Views: 926
Re: New Build LMS 3990 Hi Torque Mini Mill
might be the balls clicking, cheap ball screws make that noise.
- Tue Apr 09, 2024 3:15 pm
- Forum: Centroid Acorn CNC Controller
- Topic: RE: Circus Wiring and Trying to Get Rid of the Knock
- Replies: 19
- Views: 534
Re: RE: Circus Wiring and Trying to Get Rid of the Knock
would be good to review this at the same time.
https://www.geckodrive.com/support/step ... asics.html
https://www.geckodrive.com/support/step ... asics.html
- Tue Apr 09, 2024 3:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Coordinate display overlapping in graphing.
- Replies: 15
- Views: 473