Search found 435 matches
- Tue Jan 10, 2023 11:24 am
- Forum: Centroid Acorn CNC Controller
- Topic: G3 command stops the process <G98 vs G99>
- Replies: 9
- Views: 1090
Re: G3 command stops the process
Centroid took a look at the code and verified it would run. But there was no current report and as such could not troubleshoot this further. Looking at your report you sent, you have a spindle encoder setup in the software. Is a spindle encoder physically connected? Is it 2000 line / 8000 counts?
- Wed Dec 14, 2022 2:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: International shipping fee
- Replies: 1
- Views: 369
Re: International shipping fee
Please send it to diysales@centroidcnc.com Please let us know what you are looking to purchase and the address of where it will go.
- Mon Dec 12, 2022 4:06 pm
- Forum: Buy, Sell, Trade
- Topic: Shipping fee for Offline INTERCON
- Replies: 1
- Views: 883
Re: Shipping fee for Offline INTERCON
Hello Yelleke,
Anything International will need shipping calculated, we can check it ahead of time if you send us an email with the address. We will charge the difference left over between the $10 and what the total cost would be.
Anything International will need shipping calculated, we can check it ahead of time if you send us an email with the address. We will charge the difference left over between the $10 and what the total cost would be.
- Mon Oct 10, 2022 4:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Anyone ever run CNC12 on server hardware? in a windows VM? Through a switch?
- Replies: 3
- Views: 694
Re: Anyone ever run CNC12 on server hardware? in a windows VM? Through a switch?
To confirm, we have never tested it in those configurations. The CPU hardware is within specs, but we don't know what kind of latency will be added and what affect that could have on operational results.
- Thu Jul 28, 2022 11:12 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: New! Automation Direct SureServo2 and Oak Compatibility
- Replies: 3
- Views: 10379
New! Automation Direct SureServo2 and Oak Compatibility
Over the last few weeks we have set up and determined compatibility along with settings and parameters for using the Oak with the new Automation Direct SureServo2 drives. They run great in Position mode and also have a excellent auto-tune feature built into the drive. Attached is the drive configura...
- Mon Jul 25, 2022 8:57 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Auto/manual/timed backup software
- Replies: 6
- Views: 1311
Re: Auto/manual/timed backup software
You can schedule the backup when you boot up Windows, just wait until it is done before you proceed to do anything in the Centroid Software. However I think it would make more sense to have the backup set run as part of your shutdown procedure, so that it backs up everything after your changes of th...
- Tue Jun 21, 2022 9:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Acorn with bent pin
- Replies: 3
- Views: 823
Re: New Acorn with bent pin
Thank you for bringing that to our attention. That is clearly not how that Acorn should have shipped out. The pin in question is one of several ground pins so it will have no effect on the function of the Acorn, however we would be happy to issue an RMA. Please let us know the serial number on the A...
- Tue May 10, 2022 3:00 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Circular Connector tool(s)
- Replies: 13
- Views: 3770
Re: Circular Connector tool(s)
Can you please provide more information on which cable you are working on (photo would be best)? The connectors between probes and pendants are not the same.
- Thu Jan 13, 2022 5:00 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Shuts down / restarts on it's own
- Replies: 11
- Views: 2777
Re: Shuts down / restarts on it's own
From what I can see the Centroid Software was only started 3 times. So I don't see how it would have caused the other 10 shutdowns even if it was somehow triggering a PC shutdown. Most likely explanation is the computer is losing power. I would need to see the full Windows log however. It should sho...
- Wed Dec 15, 2021 3:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn CNC12 Mill, Router, and Lathe v4.64 has been released! < v4.80 has superseded v4.64>
- Replies: 66
- Views: 41736
Re: Acorn CNC12 Mill, Router, and Lathe v4.64 has been released!
Yes, CNC12 works on Windows 11 Home and Pro. The same Windows 10 video for setting it up can be followed, the search bar is in the center of the screen, but Control Panel stays the same.