Search found 84 matches
- Mon Jul 16, 2012 8:13 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
Thanks Scott for your help. But i need to put this problem on hold until I can get my computer to start talking to the mph11. Please look at my other thread. Thanks, Scott
- Mon Jul 16, 2012 8:10 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
Contactor does not go in when reset is hit. I checked voltage to the contactor and it is right. My motors need 90volts. So to answer your question, I don't have full power to the drive because the estop won't release. On the diaognestics page when I hit reset enable 1 ,2 ,3 light up breifly then the...
- Mon Jul 16, 2012 7:07 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
Yes i cycles the reset after the fault happened. I did also check the encoder and it is working.
- Sun Jul 15, 2012 7:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X Axis fault
- Replies: 2
- Views: 1954
Re: X Axis fault
Hi Paul, I don't know a lot on this matter or I would have my x axis drive fault figurred out but i would see if your encoder is reading both ways with motor power removed. This would at least tell you if your encoder is reading and your connections are good. Check all motor connections. Hope this h...
- Sun Jul 15, 2012 6:59 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: **Resolved** mpu11 erhernet port gone dark and no com.
- Replies: 7
- Views: 4419
**Resolved** mpu11 erhernet port gone dark and no com.
Well, if i wasn't having enough trouble with x axis fault already, now my mpu11 Ethernet port went dark. The pc is the same. I downloaded what I thought was cnc11 demo but them when it started it wanted to establish conection with the mpu11 that's when the ports stopped working. Also, the the only g...
- Fri Jul 13, 2012 1:51 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
This is a readout when i run the error test in mach3. Don't know if the error about the modbus is correct. The picture got cutt of but it says " unless using modbus, this is incorrect.".
- Fri Jul 13, 2012 1:03 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
No i don't have cnc11 installed. The number on the mpu11 is 0122100129.
- Fri Jul 13, 2012 12:37 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
Re: X axis drive fault.... need help
When you reload mach3 and the plugin do you need to uninstall them first?
- Fri Jul 13, 2012 12:30 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035
- Fri Jul 13, 2012 12:27 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X axis drive fault.... need help
- Replies: 19
- Views: 10035