Search found 114 matches

by bloomingtonmike
Tue Oct 22, 2013 10:10 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Re: Lube pump fault input questions

Looks like I have a NO float relay so I set 178 to 3 (still have to fix my spindle fault too) and set 179 to 0 and in MDI the pump runs no problem.

On the spindle CM to 9-12 common - can I connect the CM AND the 0VDC from the power supply both to 9-12COM at the same time? Would that work?
by bloomingtonmike
Tue Oct 22, 2013 9:29 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Re: Lube pump fault input questions

rtfm - just found the mill manual. I have only been reading the install manual.

I just set 179 to 0 and see continuity on outp2 :)

Bear with me as a newbie to this controller lol.
by bloomingtonmike
Tue Oct 22, 2013 8:11 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Re: Lube pump fault input questions

As for connecting the WJ200, there is a more recent post about how to do it. Dig back a little and find it- it should clear any questions up. There were two WJ200 posts - one only being the pins to connect up and another with the dialog behind it. It is those two posts that have us connecting a pin...
by bloomingtonmike
Tue Oct 22, 2013 8:08 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Re: Lube pump fault input questions

cncsnw, I have the 2.2k sips installed in all banks as I am using an external 24vdc power supply. I should be able to test the low lube input then similiarly to the estop test only inp9 - Connect 0vdc to the 9-12 common and 24V to inp9 and it should be just fine with no changes to 178 as it simulate...
by bloomingtonmike
Tue Oct 22, 2013 12:55 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Re: Lube pump fault input questions

One other question. Fault input related kinda. I hooked up my VFD (WJ200 today). I was following the instructions posted on connecting up the WJ200. It has us connect the CM2 from the WJ200 to the allinonedc's Fault com for the spindle fault. That would affect the other 3 inputs as well too correct?...
by bloomingtonmike
Tue Oct 22, 2013 12:51 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube pump fault input questions
Replies: 16
Views: 7765

Lube pump fault input questions

Can we discuss Lube pumps for a minute. I am confused. First off my pump only has four wires. Black, White, Green, Red in that order. It is a 110V pump. I was thinking I would: run hot/line through the output for Lube (3&4 terminals on top of controller) Run 110 neutral to the pump run 24V+ thro...
by bloomingtonmike
Sun Oct 20, 2013 9:17 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Cnc Mill Build
Replies: 10
Views: 5958

Re: Cnc Mill Build

Getting further along. Made it past step 8.

http://www.youtube.com/watch?v=av4r68cCPxs
by bloomingtonmike
Sat Oct 19, 2013 3:05 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Cnc Mill Build
Replies: 10
Views: 5958

Re: Cnc Mill Build

Got the encoders wired. The original dynapath delta 20 had a DB37 connector for the encoders so rather than destroying that I bought a DB37 breakout DIN rail mountable break out connector. I wired it up to three BTX MaxBlox DB9 Male connectors - so all connections were screw down terminals. Also got...
by bloomingtonmike
Wed Oct 16, 2013 2:21 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Cnc Mill Build
Replies: 10
Views: 5958

Re: Cnc Mill Build

Been working on the wiring a lot. Have most every "system" wired in that comes in from conduit. The VFD's power is wired in and it is connected to the spindle. I have motion on the spindle. Also have all the power circuits wired in - 220V, 110V transformer, 72V/79V transformer and cap/rect...