I usually make the first run with a shorter than needed length, measure, adjust and second run is perfect, since it is no problem to tap a thread twice.
Uwe
Search found 2172 matches
- Sat Jun 01, 2024 11:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: Adjusting Rigid Tapping Parameters
- Replies: 6
- Views: 85
- Sat Jun 01, 2024 11:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: The Centroid CNC PC Tuner v1.3.0 has been released.
- Replies: 29
- Views: 29408
Re: The Centroid CNC PC Tuner v1.3.0 has been released.
Windows defender is working ok with CNC12, but I also allow LAN only for updates or if I use CAM to post gcode...
Uwe
Uwe
- Sat Jun 01, 2024 10:19 am
- Forum: Centroid Acorn CNC Controller
- Topic: The Centroid CNC PC Tuner v1.3.0 has been released.
- Replies: 29
- Views: 29408
Re: The Centroid CNC PC Tuner v1.3.0 has been released.
For PC tuner PC must have internet connection and it must be set up to US Keyboard, Number and Date format..
Uwe
Uwe
- Sat Jun 01, 2024 9:45 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Feature Request - SSV
- Replies: 34
- Views: 2688
Re: Feature Request - SSV
Video of my stupid simple version at work
Uwe
Uwe
- Sat Jun 01, 2024 4:41 am
- Forum: Centroid Acorn CNC Controller
- Topic: Adjusting Rigid Tapping Parameters
- Replies: 6
- Views: 85
Re: Adjusting Rigid Tapping Parameters
CNC12 is not with closed loop control of the spindle at 0-10V An exactly stop at depth in the g code will not be possible, but the small overshoot is exactly reputable in the same material The dwell will do noting, but the spindle drift. Air tapping will go deeper than in aluminum, an aluminum deepe...
- Fri May 31, 2024 6:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Z Axis lag - Loosing position
- Replies: 14
- Views: 759
Re: Z Axis lag - Loosing position
Do you not use a WMPG?
If not, using an input for a FeedHold / CycleStart switch is also no big deal.
Uwe
If not, using an input for a FeedHold / CycleStart switch is also no big deal.
Uwe
- Fri May 31, 2024 1:14 am
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 13
- Views: 237
Re: No signal from Acorn to the stepper drivers
Common cause of drives not responding after update is different setting of Enable in the Wizard Advanced Axis setup.
Uwe
Uwe
- Thu May 30, 2024 12:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ProbeApp V3: The Ultimate Probe Software for CNC12
- Replies: 74
- Views: 124779
Re: ProbeApp V3: The Ultimate Probe Software for CNC12
ProbeApp will work with 5.10
Uwe
Uwe
- Thu May 30, 2024 12:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Finally did a fresh install and WPMG still not being recognized by windows
- Replies: 19
- Views: 418
Re: Finally did a fresh install and WPMG still not being recognized by windows
copy the cncm folder on a thumb drive and back after recovery.
Uwe
Uwe
- Thu May 30, 2024 12:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Finally did a fresh install and WPMG still not being recognized by windows
- Replies: 19
- Views: 418
Re: Finally did a fresh install and WPMG still not being recognized by windows
You can also try to use a recovery point from a time the WMPG was working...
Uwe
Uwe