This is the post I had seen using Fusion 360 with Centroid and rigid tapping. I believe they are using the same post that I am.
https://centroidcncforum.com/viewtopic. ... 351#p81351
Richard
Search found 401 matches
- Fri May 24, 2024 4:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
- Fri May 24, 2024 3:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Re: Rigid Tapping Question
If I choose to use a tapping head, do I simply disable rigid tapping in the wizard?
- Fri May 24, 2024 3:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Re: Rigid Tapping Question
I thought I had seen others using Fusion 360 and rigid tapping with Centroid. I had no idea that this would be an issue.
- Fri May 24, 2024 3:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Re: Rigid Tapping Question
I will give it a try.
- Fri May 24, 2024 2:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Re: Rigid Tapping Question
Thanks again for getting back to me so quickly. A bit disappointing news. I am still learning both Fusion and G-code, so some of this is a bit over my head. I too played with the "use feed per revolution" and it made no difference. Before attempting rigid tapping, I posed the question on t...
- Fri May 24, 2024 11:26 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Re: Rigid Tapping Question
Thanks! I did not see an option for "use canned cycles" or similar, so I am curious as to what settings you are using. Thanks for your reply.
Richard
Richard
- Fri May 24, 2024 2:25 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 16
- Views: 101
Rigid Tapping Question
I setup a test sample with Fusion 360 to experiment with rigid tapping holes for the 1st time. The test sample has a number of holes that I intend to drill and tap using machining wax so I can tweak the mill's rigid tapping parameters to achieve the best possible tapped holes. On the Design side, I ...
- Thu May 23, 2024 1:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 16
- Views: 692
Re: AC Servo suggestions?
Good question, The 2.6KW model I ordered was discontinued and replaced with another very similar model. Please see email below from JMC that details exactly what was ordered for my friend. It looks like the driver is a JASD. I have attached this manual. From: Holly-JMC <sales1@jmc-motion.com> Sent: ...
- Thu May 23, 2024 12:54 am
- Forum: Centroid Acorn CNC Controller
- Topic: Commanded Speeds Vs Actual Spindle Speed
- Replies: 3
- Views: 92
Re: Commanded Speeds Vs Actual Spindle Speed
Thanks for your quick response! I agree that the difference of two hundred RPM will have no effect on the parts I am milling. My goals is to have the lower commanded rpm as accurate as possible as I am getting ready to start rigid tapping. I think for now I will leave everything as is and try to do ...
- Wed May 22, 2024 8:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: AC Servo suggestions?
- Replies: 16
- Views: 692
Re: AC Servo suggestions?
I purchased a 2.6KW JMC servo for a spindle motor for myself on ebay, then ordered another one for a friend directly from JMC. The 2.6KW servo with driver delivered to Texas was about $500.00. My contact at JMC is: Holly sales1@jmc-motion.com They were very accommodating and helpful with a few techn...