Thank you! I believe that Andrew added the code to the post I was using (Centroid_MillRev-40783-swissi-005.cps). Did you copy the code to a new version?'
Richard
Search found 433 matches
- Sat May 25, 2024 11:52 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
- Sat May 25, 2024 12:35 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
Thanks for the explanation, very helpful. Yes. I agree. The manual says you "may" use a Q value, however I could not make it work without one. A very nice dude on the Fusion CAM forum from New Zealand (Andrew Laas) who has helped me many times with Fusion, was nice enough to modify the Pos...
- Fri May 24, 2024 7:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
I hate giving up so I tried to better understand this. We have been discussing the fact that Fusion 360 was not outputting a Q value. As you pointed out, the manual says: Note: If rigid tapping is enabled, a Q may be used to set the thread lead or pitch. However, because Q is not modal in the case o...
- Fri May 24, 2024 6:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
Thanks Uwe. I have to think about this one for a bit. Not sure if it is worth the time to modify the g-code each time I want to rigid tap, or use Intercon instead. Neither is what I had in mind. On the other hand, adding a Q value to each line may not be that bad.
- Fri May 24, 2024 4:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
This is the post I had seen using Fusion 360 with Centroid and rigid tapping. I believe they are using the same post that I am.
https://centroidcncforum.com/viewtopic. ... 351#p81351
Richard
https://centroidcncforum.com/viewtopic. ... 351#p81351
Richard
- Fri May 24, 2024 3:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
If I choose to use a tapping head, do I simply disable rigid tapping in the wizard?
- Fri May 24, 2024 3:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
I thought I had seen others using Fusion 360 and rigid tapping with Centroid. I had no idea that this would be an issue.
- Fri May 24, 2024 3:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
I will give it a try.
- Fri May 24, 2024 2:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
Thanks again for getting back to me so quickly. A bit disappointing news. I am still learning both Fusion and G-code, so some of this is a bit over my head. I too played with the "use feed per revolution" and it made no difference. Before attempting rigid tapping, I posed the question on t...
- Fri May 24, 2024 11:26 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Question
- Replies: 39
- Views: 1146
Re: Rigid Tapping Question
Thanks! I did not see an option for "use canned cycles" or similar, so I am curious as to what settings you are using. Thanks for your reply.
Richard
Richard