sending you the detailsdiycncscott wrote: ↑Wed Feb 21, 2018 10:27 am Simon
Please install Teamviewer 12 available here: http://download.teamviewer.com/download ... _Setup.exe
Our license has not been upgraded to 13 yet.
Search found 12 matches
- Wed Feb 21, 2018 10:47 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
- Wed Feb 21, 2018 10:09 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
FWIW The OP was emailed the "imperial work around" earlier and confirmed it did take care of his issue. The issue has been resolved and the work around will no longer be needed in the next release for Acorn (towards the end of this month). It has also been resolved in CNC12 closed loop sy...
- Tue Feb 20, 2018 7:27 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
Metric threads are stated in mm/rev unlike imperial threads which are stated as rev/inch. Consult your drive and motor docs to first get your motor steps/rev squared away before worrying about mm's/rev. Steps/rev is a fixed value that doesn't change with ball screw pitch, rack and pinion ratios, pu...
- Tue Feb 20, 2018 3:54 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
Module = 1. Pitch diameter = 30. Number of teeth = 30Gary Campbell wrote: ↑Tue Feb 20, 2018 2:28 am Do you have a part number for the pinion? How about the pitch module and number of teeth?
- Tue Feb 20, 2018 1:55 am
- Forum: Centroid Acorn CNC Controller
- Topic: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
- Replies: 11
- Views: 3900
Re: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
Ok, Looking at the picture there is no Limit switch connections to this drive but there is a USB port. Having used similar leadshine drives I have connected the special cable and checked to see how the drive was programmed. http://www.yankong.com/EN/proview-54-23.html I went to this site and looked...
- Tue Feb 20, 2018 12:56 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
Metric threads are stated in mm/rev unlike imperial threads which are stated as rev/inch. Consult your drive and motor docs to first get your motor steps/rev squared away before worrying about mm's/rev. Steps/rev is a fixed value that doesn't change with ball screw pitch, rack and pinion ratios, pu...
- Mon Feb 19, 2018 10:43 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
Re: calculating turns ratio for a rack and pinion
IF pitch diameter is 30 then circumference is 30 * pi or 94.24778mm 1 / 94.24778 = 0.01061 revolutions per mm I would recommend both adding mechanical reduction and increased microstepping to at least 1/8 or 1600 steps/rev thanks for the reply Gary. however, the wizard is asking for mm/revolution a...
- Mon Feb 19, 2018 9:42 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: calculating turns ratio for a rack and pinion
- Replies: 25
- Views: 7633
calculating turns ratio for a rack and pinion
Hello, hello. I am still new to centroid. Am using it to make my CNC and the axes are moved by a rack and pinion. my pinion pitch diameter is 30mm. it is coupled to the motor directly (no gear ratio) my steps/revolution is (800). I have set this both in the driver and the wizard. I want to set my tu...
- Sat Feb 17, 2018 2:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
- Replies: 11
- Views: 3900
Re: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
Ok, Looking at the picture there is no Limit switch connections to this drive but there is a USB port. Having used similar leadshine drives I have connected the special cable and checked to see how the drive was programmed. http://www.yankong.com/EN/proview-54-23.html I went to this site and looked...
- Fri Feb 16, 2018 2:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
- Replies: 11
- Views: 3900
Re: RE: CLOSE LOOP MOTOR MOVES ONLY IN ONE DIRECTION
It is stressing me out. I tried and the behavior is the same from both the screw connections and DB25.Gary Campbell wrote: ↑Fri Feb 16, 2018 1:47 pm This is weird, but I had that condition once when the dir+ and dir- wires were reversed. The drive silkscreen was wrong
Have you tried taking signal from the DB25 connector?