Search found 54 matches
- Wed Nov 25, 2020 9:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: spindle reverse button issues
- Replies: 7
- Views: 2832
spindle reverse button issues
I just updated my lathe to the newest cnc12. didnt go very smoothly but i was able to get everything to work. only issue im having is on the vcp the spindle reverse button acts like a momentary switch. my mill and the lathe before updating if you hit the reverse direction button it would run that wa...
- Wed Nov 25, 2020 9:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: updated software now no stepper movement (Resolved)
- Replies: 3
- Views: 2005
Re: updated software now no stepper movement
i just had this same issue. did you set the correct connection db25 or screw terminal. if that's not it check your enable pins
- Fri Nov 06, 2020 9:47 am
- Forum: Centroid Acorn CNC Controller
- Topic: syncing of spindle with 4th axis
- Replies: 0
- Views: 2414
syncing of spindle with 4th axis
Is it possible to sync the spindle rotation with the rotation of a 4th axis to hob on a mill? im thinking it might be possible if you set up the 4th as a linear axis and run a tapping cycle maybe but wonder in there might be a better way?
- Thu Jun 06, 2019 9:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: One problem fixed. Now a new one. FIXED
- Replies: 6
- Views: 3234
Re: One problem fixed. Now a new one. FIXED
I contacted DMM and they said the enable circuit should work and if not i will need to add a time delay so the drives power off before the acorn. i added a enable circuit with 270ohm resistors. fixed the problem. now i have to work on cleaning up my terrible wiring.
- Wed Jun 05, 2019 10:45 am
- Forum: Centroid Acorn CNC Controller
- Topic: One problem fixed. Now a new one. FIXED
- Replies: 6
- Views: 3234
Re: One problem fixed. Now a new one. Please Help
The ENA signal is an Enable signal which some drives require to tell it that it should be expecting signals to spin the motor. By default, the ACORN will pull the ENA output to COM when it's energized. If you are using the screw terminals, the ENA is an open collector output which means that the ou...
- Wed Jun 05, 2019 10:43 am
- Forum: Centroid Acorn CNC Controller
- Topic: One problem fixed. Now a new one. FIXED
- Replies: 6
- Views: 3234
Re: One problem fixed. Now a new one. Please Help
Yes i followed the centroid schematic. only wires i omitted for now was the alarm connections. im using a 600w 60v antek toroidal.
Is there any way to use the enable pin? the dyn requires 5v to the pin and the ena out on the acorn is to common i believe.
Is there any way to use the enable pin? the dyn requires 5v to the pin and the ena out on the acorn is to common i believe.
- Tue Jun 04, 2019 8:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: One problem fixed. Now a new one. FIXED
- Replies: 6
- Views: 3234
Re: One problem fixed. Now a new one. Please Help
If i unplug the DB25 before hitting the main power there is no movement.
- Tue Jun 04, 2019 8:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: One problem fixed. Now a new one. FIXED
- Replies: 6
- Views: 3234
One problem fixed. Now a new one. FIXED
When i power off my mill all 3 axis jump about an 1/8 inch to the positive. Power off procedure: Park Power Off (wait for the computer to shut down) Hit the switch on the power supply Its when i hit the switch and kill power to everything its jumping. Machine specs. pm25mv procut cnc conversion dmm ...
- Tue Jun 04, 2019 8:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Spindle interference with Z axis
- Replies: 4
- Views: 2296
Re: Spindle interference with Z axis
switched my wiring over to the db25 plug and z seems fixed but now i have a new problem. will make new topic
- Mon Jun 03, 2019 8:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Spindle interference with Z axis
- Replies: 4
- Views: 2296
Re: Spindle interference with Z axis
when z is stationary there is no movement. i did run z down 5 inches and back to tool check a few times and it lost .015 with the spindle running at max 2500. was only about .002 lost when the spindle is not running. in searching the forum i found i should have my dyn2 hooked up through the db25 con...