Search found 2203 matches
- Tue May 07, 2024 11:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 6
- Views: 80
Re: Help on isolation switch fit two circuits/power supplies
A few observations: In my experience, usually the spindle would be on a higher amperage circuit than the control Is there a reason to not use a single, higher amperage circuit? I prefer using a load break switch, usually door mounted as an added safety feature Your spindles VFD and the drives power ...
- Mon May 06, 2024 8:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 Software cycle start disabled
- Replies: 10
- Views: 142
Re: CNC12 Software cycle start disabled
Well said Marc. There is a deep rooted long standing "programmer bias" in the PLC code intentionally set for reasons I cannot wrap my head around. Normally open and closed devices are binary, in other words, as simply as any actionable device can be. 2 choices, represented as zero or one. ...
- Sat May 04, 2024 6:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ethernet communication errors...wits end
- Replies: 8
- Views: 197
Re: ethernet communication errors...wits end
Go to the LAN adapters mfgr website and update the driver(s)
- Sat May 04, 2024 11:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: Tool Change Macro Help
- Replies: 26
- Views: 534
Re: Tool Change Macro Help
I agree. As someone who runs multiple acorns the only thing i would prefer is if they included 1-2 hours of centroid tech support with the purchase. The forum based support is ok for most things but not ideal for digging into the weeds, something like this. They do, just not on the same page as the...
- Fri May 03, 2024 9:43 am
- Forum: Centroid Acorn CNC Controller
- Topic: Controller-only (not motors/drivers) upgrade for PRS Alpha
- Replies: 18
- Views: 329
Re: Controller-only (not motors/drivers) upgrade for PRS Alpha
Yes, Oriental's docs are thorough, if not close to overwhelming! If you can simply reset to factory defaults, they will work just fine with most controllers. If you do succeed, there may be a cottage industry there for you!
- Fri May 03, 2024 8:01 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Shopbot conversion: tech help needed
- Replies: 2
- Views: 97
Re: New Shopbot conversion: tech help needed
Agreed. One of the "Door Safety" input designations should work the way you want. In my travels as a SB service tech that key switch with the spindle wrench attached was the second most requested safety feature to remove. In first place was the 2 second "Ooo-Aah, Ooo-Aah, Ooo Aah"...
- Thu May 02, 2024 8:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Controller-only (not motors/drivers) upgrade for PRS Alpha
- Replies: 18
- Views: 329
Re: Controller-only (not motors/drivers) upgrade for PRS Alpha
If you're diligent you can probably find a way to reprogram the drives online. It used to take usb to rj45 adapter cable and M$ hyper terminal
- Thu May 02, 2024 6:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Controller-only (not motors/drivers) upgrade for PRS Alpha
- Replies: 18
- Views: 329
Re: Controller-only (not motors/drivers) upgrade for PRS Alpha
Hey man, I'm not trying to sell you a controller package, just trying to save you some wasted time and frustration. There are a good number of SB guys here that have built their own systems, and they, along with myself try to assist the next guys that come along
- Thu May 02, 2024 5:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Controller-only (not motors/drivers) upgrade for PRS Alpha
- Replies: 18
- Views: 329
Re: Controller-only (not motors/drivers) upgrade for PRS Alpha
Thanks, Gary. I just read that post, and I see your point. However, it seems to me that overall it should be more practical with the 2020 hardware since the motor/driver issues you mentioned have presumably been addressed. You may have missed the line where I stated that the more modern drive (AR) ...
- Thu May 02, 2024 5:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Controller-only (not motors/drivers) upgrade for PRS Alpha
- Replies: 18
- Views: 329
Re: Controller-only (not motors/drivers) upgrade for PRS Alpha
All has been answered here by me, with one small caveat: the 2020 version of drivers (AR versions) will be slightly more difficult to implement as they have even more obscure logic in their programming
https://centroidcncforum.com/viewtopic.php?t=10052
https://centroidcncforum.com/viewtopic.php?t=10052