Search found 9 matches

by dbunyip
Thu Jan 04, 2018 1:58 am
Forum: Centroid Acorn CNC Controller
Topic: Start program at line number <answered>
Replies: 2
Views: 52

Start program at line number <answered>

Is there a way to start a program at a certain line number?
by dbunyip
Sat Dec 23, 2017 10:54 pm
Forum: Centroid Acorn CNC Controller
Topic: Feed rate not consistant
Replies: 5
Views: 108

Re: Feed rate not consistant

Here is the report, still working on a smaller post file example. The one I noticed it on is a huge file
by dbunyip
Sat Dec 23, 2017 2:01 pm
Forum: Centroid Acorn CNC Controller
Topic: Feed rate not consistant
Replies: 5
Views: 108

Feed rate not consistant

I'm using fusion 360 with centroid post. Haven't got to dig into it yet but just noticed when cutting arcs the feed rate doubles. Quick search didn't come up with anything on it but it does start to explain why the actual cut time is way less then the estimated time. Any one experience this? I'm gue...
by dbunyip
Sun Dec 03, 2017 7:12 pm
Forum: Centroid Acorn CNC Controller
Topic: Quencharc
Replies: 3
Views: 97

Re: Quencharc

On 220v they go across L2 and L2 at the motor?
by dbunyip
Sun Dec 03, 2017 3:28 am
Forum: Centroid Acorn CNC Controller
Topic: Quencharc
Replies: 3
Views: 97

Quencharc

Does anyone have pictures of how the Quencharc are supposed to be installed. The TB206.pdf document only shows 1 of the pictures for me. Does it only take 1 across the 2 coil terminals or does it go across the 2 power lines as well on the contactor?
by dbunyip
Fri Dec 01, 2017 3:03 pm
Forum: Centroid Acorn CNC Controller
Topic: Activating outputs based on tool number
Replies: 5
Views: 133

Re: Activating outputs based on tool number

another question, If I used "IF #4120 == 1 THEN #5041 = #5041 + 2" would that shift my WCS by 2in? I'm not in front of my machine right now but I'm going to try in a few hours and see if I can figure out that part. I know I'm going to need more to have a way to put it back but I need to move WCS by ...
by dbunyip
Fri Dec 01, 2017 1:21 pm
Forum: Centroid Acorn CNC Controller
Topic: Activating outputs based on tool number
Replies: 5
Views: 133

Re: Activating outputs based on tool number

Thank you very much. Do I have to set the parameters for atc to use the mfunc6.mac?
by dbunyip
Fri Dec 01, 2017 2:06 am
Forum: Centroid Acorn CNC Controller
Topic: Activating outputs based on tool number
Replies: 5
Views: 133

Activating outputs based on tool number

Is it possible to activate an output by which tool number is called?

When T1 is called I want to pause program for 1sec, activate output 7 then continue program.

Same with T2 and output 8

And If any other tool number is called, fault out
by dbunyip
Sun Nov 12, 2017 12:49 pm
Forum: Centroid Acorn CNC Controller
Topic: Dual spindle router
Replies: 0
Views: 99

Dual spindle router

Lioking for more info on how to configure my routers dual spindles. Just purchased acorn for it to replace the garbage thing it came with and trying to plan and prep for fastest change over and haven't seen one of these done yet but was told on cnczone that it was no problem to do. The current contr...