Search found 91 matches
- Mon Feb 26, 2024 7:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can someone give me a hand with Intercon Lathe Chamfers?
- Replies: 13
- Views: 1863
Re: Can someone give me a hand with Intercon Lathe Chamfers?
Thanks for the tip on where to position the tool before programming a chamfer. "all the manual has to say is position the tool tip where you want to start the chamfer before programming a chamfer" Wouldn't it be easier to have a centre point for the middle of the chamfer and how long you w...
- Thu Feb 22, 2024 8:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: Tool offsets Lathe
- Replies: 4
- Views: 302
Re: Tool offsets Lathe
If you have set Z Ref with the probe, manual Z measure at another Z position than that of the probe will not work. If I have to set Z for a tool and do not want to use the probe while a part ist in the spindle, I make sure the tool is selected and drive it to part Z 0. Than I correct its Z offset s...
- Thu Feb 22, 2024 6:58 am
- Forum: Centroid Acorn CNC Controller
- Topic: G&M code file loading into Acorn Lathe
- Replies: 2
- Views: 169
G&M code file loading into Acorn Lathe
I am trying to cut a 14mm deep by 28mm long groove in a piece of aluminium bar on a lathe. It has to have a 2mm radius fillet in the bottom corners. I need to use a parting blade 3.2mm wide to cut the groove. The only way to program it on intercon is to use the profile and face cutting for stock rem...
- Tue Feb 20, 2024 3:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Tool offsets Lathe
- Replies: 4
- Views: 302
Re: Tool offsets Lathe
The width of the probe is only for auto measure ZX, so after measuring Z the CNC knows the center of the probes width. Measuring drills in X with the probe is a "bad habit", because if the drill edge is not exactly set in height you get wrong values, set X0 of the toolholder with a dial i...
- Tue Feb 20, 2024 11:28 am
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe CAM post processor
- Replies: 2
- Views: 179
Re: Lathe CAM post processor
I had a look at the files but it needs a lib and PP file for catiaNigelo wrote: ↑Tue Feb 20, 2024 8:56 am Since both Catia and Solidworks are under the Dassault umbrella, perhaps the following post may help
https://centroidcncforum.com/viewtopic.php?f=60&t=4101
- Tue Feb 20, 2024 8:37 am
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe CAM post processor
- Replies: 2
- Views: 179
Lathe CAM post processor
Is there a specific CAM post processor for Catia V5 I use the CAD software at work but can't find a suitable CAM post processor for centroid. I have tried Haas and Fanuc but they are not correct.
- Mon Feb 19, 2024 7:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: Tool offsets Lathe
- Replies: 4
- Views: 302
Tool offsets Lathe
I figured out why the "Lathe" Z tool offsets were out by 7.5mm when doing a manual tool offset measurement. In the probe setup page where you put the measurements of the probe i had the width of the probe stylus set to 7.5mm. Why this affects a manual tool offset is a problem for Centoid t...
- Thu Feb 08, 2024 2:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: How to set up drills with auto touch off probe. LATHE
- Replies: 5
- Views: 752
- Sat Feb 03, 2024 5:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: How to set up drills with auto touch off probe. LATHE
- Replies: 5
- Views: 752
Re: How to set up drills with auto touch off probe. LATHE
I'm not experienced here but I saw there were no replies so.. My question is- I understand setting the Z of the drill but the X should just always be the center line- so could you just get away with measuring your drill chuck/collect center and recording that X offset fro your reference tool and al...
- Fri Feb 02, 2024 5:05 am
- Forum: Centroid Acorn CNC Controller
- Topic: Spindle bench test not showing full text
- Replies: 5
- Views: 424