Search found 13 matches
- Wed Mar 13, 2024 9:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Control Panel Circuit Protection
- Replies: 6
- Views: 294
Re: Control Panel Circuit Protection
Hi Shawn, thank you for that information, its very helpful. The backplane is metal. What would your recommendation be for grounding the cabinet? I have a busbar that I plan on running the ground from each device to, but still unsure of the best way to ground the cabinet itself. Would I run the groun...
- Tue Mar 12, 2024 12:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Control Panel Circuit Protection
- Replies: 6
- Views: 294
Re: Fusing of Control Panel
Thanks Shawn and I was not sure whether using fuses or circuit breakers would be better (title shows some of my lack of knowledge and inexperience but I am trying my best with it all). The power will be coming from a 30A 208V feed from the circuit breaker that goes into a knife switch and then from ...
- Tue Mar 12, 2024 10:21 am
- Forum: Centroid Acorn CNC Controller
- Topic: Control Panel Circuit Protection
- Replies: 6
- Views: 294
Control Panel Circuit Protection
Looking for some advice on protecting the components in the control panel. I am open to any suggestions and input because I have reached a bump in the road with the electrical aspect of this project. I have primarily been looking at adding a fuse to the input of each device. I am looking at feeding ...
- Fri Mar 01, 2024 11:24 am
- Forum: Centroid Acorn CNC Controller
- Topic: Limit Switches and VFD Wiring
- Replies: 0
- Views: 1256
Limit Switches and VFD Wiring
Update on a previous post, but in the process of building a three axis CNC gantry mill. For the most part, the mechanical side of the machine is complete for now and I am feeling good with where its at. I have had all three axis of the physical machine moving and have been fine tuning Overall Turns ...
- Wed Feb 28, 2024 12:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New CNC Mill Build Need Wiring Help!
- Replies: 11
- Views: 1507
Re: New CNC Mill Build Need Wiring Help!
Update on the build, for the most part, the mechanical side of the machine is complete for now and I am feeling good with where its at. I have had all three axis of the physical machine moving and have been fine tuning Overall Turns Ratio and Backlash compensation. Now, I have been working on final/...
- Thu Jan 04, 2024 10:51 am
- Forum: Centroid Acorn CNC Controller
- Topic: VFD Selection for Use with Acorn
- Replies: 4
- Views: 1879
Re: VFD Selection for Use with Acorn
Thank you for your help Wes. Another newbie question, but right now during the building and testing stages of the machine, I have the meanwell power supply that came with the Acorn connected to a standard 110/120 V outlet. If the spindle motor requires 230VAC, do I switch the power incoming to the m...
- Wed Jan 03, 2024 6:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD Selection for Use with Acorn
- Replies: 4
- Views: 1879
VFD Selection for Use with Acorn
Looking for some guidance on selecting a VFD for my spindle motor and pairing it with the Acorn and CNC12 software. The spindle motor I am going to be using is a Suhner BEX35. I will attach a picture of the motor nameplate below. I am looking at the specs on the nameplate for 230V at 60 Hz since I h...
- Tue Aug 29, 2023 12:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New CNC Mill Build Need Wiring Help!
- Replies: 11
- Views: 1507
Re: New CNC Mill Build Need Wiring Help!
Another question regarding the wiring and electrical aspect of this project.
Using the three stepper motors and drives above, do I need a power supply for each motor and drive or is one sufficient?
Using the three stepper motors and drives above, do I need a power supply for each motor and drive or is one sufficient?
- Mon Aug 21, 2023 3:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Questions Regarding Converting a Lodge & Shipley Engine Lathe to CNC
- Replies: 1
- Views: 280
Questions Regarding Converting a Lodge & Shipley Engine Lathe to CNC
Relatively new to the forum but have been getting great help on another project, so I figured I would seek some advice on a new project. We are looking to convert an old Lodge and Shipley 20.5” x 78” Powerturn Engine Lathe Model 2013 to be a CNC using the Acorn board. We do not use the lathe for act...
- Thu Aug 17, 2023 3:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New CNC Mill Build Need Wiring Help!
- Replies: 11
- Views: 1507
Re: New CNC Mill Build Need Wiring Help!
Update... Everything seems to be working appropriately so far. I have two out of the three motors and drives hooked up as well as a functioning E-stop now. Now going to work on configuring everything and adjusting some parameters as well as learning/experimenting more with the CNC12 software. Thank ...